Geek Smart L-B201 Fingerprint Door Lock User Manual

Geek Smart L-B201 Fingerprint Door Lock

How To Use

Specifications

Welcome
GeekSmart bids you welcome to a world of smart home devices, smart locks, and smart surveillance.
We at GeekSmart strive to explore and develop the the smart home industry for the good of all. We combine bridge cutting-edge technologies to develop products fit and ready for the market.
Please visit our website www.geektechnology.com
Before installing, please scan the QR codes to watch our easy step-by-step installation video.
If you have questions regarding the installation process please contact us by mail
customercare@geektechnology.com or by phone 1-844-801-8880/ (862)352-0406.

Product Description

Preparing For Installation

Include in the box

• A. Front handle

• B. Rear handle
  

• C. Latch

• D. Strike parts

• E. Keys

• F. Screws B x4

• G. ScrewsAx4

• Gasket

• 2 3/8″(60mm)
  

• 2 3/4″ (10mm)
  

Check the door’s dimensions

Step 1: Measure to confirm that the door is between 11/8″~2″ (35mm~55mm) thick
Step 2: Measure to confirm that the hole in the door is 2″ (55 mm)
Step 3: Measure to confirm that the backset is either 2% “~ 2¾” {60~70mm)
Step 4: Measure to confirm that the hole in the door edge is 1″ (25 mm)

Installing Latch and Strike Plate

1. Install latch on the door. Make sure the latch angle faces door jamb.
2. Install the strike on the door frame, ensuring you allow for the bolt to be centered in the strike.
   

Installing Battery

1. Disassembly battery cover by screwdriver.
2. Insert 4* AAA batteries according to positive and negative pole.
3. Install battery cover, and secure it with the screw.
   

Installing Exterior Handle

Remember to attach rubber gasket to handle before insertion.

Installing Interior Handle

1. Connect the cable from inside spindle of exterior handle with interior handle.
   

2. Insert interior handle into door, secure it using screw B into the exterior handle.

Lock Operation

Use a microfiber cloth and wipe across the fingerprint reader surface.
NOTE: THE FIRST 2 FINGERPRINTS ADDED ARE ADMINISTRATOR. When 2 ad min- user fingerprints have been collected, adding new fingerprints will prompt normal-user fingerprint collection. CD Adding fingerprints
Method 1: Use pin to press the “settings-button” on the interior handle shortly. You’ II be asked to scan your fingerprint. Scan your fingerprint 6 times in sequence. Upon completion, LED will light blue for 2 seconds and the lock will prompt “Addition Success”
Method 2: Hold your fingerprint to scanner for about 10 seconds until you hear “add administrator fingerprint”. Scan new fingerprint 6 times. Upon completion, LED will light blue for 2 seconds and the lock will prompt “Addition Success”.

* Please note the following factors may affect the fingerprint identification.

1. Fingers are too dry, wet, oily or dirty.
2.There is direct sunlight on the sensor.
2 Passage mode
In passage mode the lock will stay unlocked for convenient free passage.
Q:Howto enable passage mode?
A1: Press the mode-switching button on the interior handle to change between modes.
A2: Admin scans fingerprint for 17 seconds until you hear “set to normally open”. LED light flashes 3 times.
Q: How to disable passage mode?
A: Press the mode-switching button on the interior handle to change between modes.
Q: How to enable or disable silent mode?
A: Long press the mode-switching button on the interior handle to change.
3 Delete all fingerprints (Factory Reset)
Use pin to hold press the pin-button on the interior handle for 5-6 seconds. After prompting “initialization success” the lock has been reset and ALL FINGERPRINTS (INCLUDING ADM INS).
4 Additional Information & notices
a. Upon failed fingerprint verification, the LED flashes red for 4 seconds.
b. Upon timed out or abnormal operation, the LED lights for 2 seconds.
c. Please keep at least one key in secure location outside of your place.
d. If the fingerprint scanner fails to recognize your fingerprints, try to wipe the scanner and your fingers.
**5** What notification will receive when the battery is low?
a. Blinking red light: Battery power is low, need to replace battery.

Specifications

FCC warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CUSTOMER SERVICE

Geek Technology Co.Ltd.
120 Route 46 West,
Parsippany, NJ 07054.
Toll Free
1-844-801-8880
(862)352-0406

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>