INTELLINET 163682 19 Inch Intelligent 8-Port PDU User Manual

: June 11, 2024
: INTELLINET

Table of Contents

Before You Begin
Getting Started
Product Diagram
Functions
Additional Information
- REGULATORY STATEMENTS FCC Class B
For additional benefits:
Customer Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INTELLINET 163682 19 Inch Intelligent 8-Port PDU

Before You Begin

Read through this manual carefully before using the product and operate it according to the manual. Keep it in an easily accessible location for future reference.

Do not disassemble the device or remove the seal label from the device.
Doing so will void the Intellinet product warranty.

All pictures in this manual are for reference only. The actual product may differ. Intellinet reserves the right to make changes to any software or hardware to improve reliability, function, or design at any time without notice. The information contained herein is subject to change without prior notice.

No user, corporation or individual, shall duplicate, in whole or in part, distribute, modify, decompile, disassemble, decode, reverse engineer, rent, transfer or sublicense such software without prior written consent from the copyright holders.

This manual is copyrighted. No part of this publication may be reproduced, distributed or used in any form without written permission from Intellinet Network Solutions.

Getting Started

Product Overview

The Intellinet 19” Intelligent 8-Port PDU helps provide steady power to keep network equipment active. It monitors electricity and environmental status to provide users with relevant information and alert them of potential power overloads. The user can readily view equipment status and turn on or shut off each output port by accessing the device through the network.

Product Features:

Eight power outputs (total current, 16 A)
Current, voltage (total input) measurements
Built-in temperature and humidity sensors to monitor the environment
Embedded technology, Java support, web browsing
Two-level programmable values for warning and overload
Circuit-delay time setting to prevent power surges
LED indicators for the power supply on each switch
LED digital display to show the current value of voltage and current
Local query buttons of PDU equipment
Built-in lightning- and voltage-surge resistance to effectively protect connected equipment

Product Specifications:

Voltage input: 110-240 V, 50/60 Hz
Voltage output: 110-240 V, 50/60 Hz
Input socket type: IEC320 C20, *1 bit
Output socket type: IEC320 C13, *8 bits
Protection: 16 A overload protection, lightning protection
Voltage measurement range: 90 – 264 VAC, resolution 1 V
Current working range: 0 – 20 A, resolution 0.1 A
Temperature measurement range: 20% -90% RH, resolution 1% RH
Humidity measurement range: 0 – 50°C, resolution 1°C

Product Diagram

Key

Power Input Socket: IEC320 C20
Output Socket: IEC C13
Reset Key
Function Key: check the machine IP address
Display Panel: voltage, current, temperature, humidity, etc.
Network Port: connect LAN or WAN

Functions

Basic Functions

Connecting and Powering Equipment: Connect the input power cords from your server/network equipment to the output ports on the Intellinet 19” Intelligent 8-Port PDU. Connect one end of a power cord to the input socket and the other to an AC wall outlet. By default, the Intelligent PDU will then power up each power-out socket from ports one through eight at one-second intervals. The display panel will show the current supply voltage and total power output as well as the LED indicator lights.
Cycle through statuses: Press FUNC briefly and repeatedly to review statuses for current-voltage interface, temperature and humidity, and to show IP address.
Restore factory default settings: Press and hold FUNC (approx. 10 seconds).
Quick Restart: Press RST.
Network access and control: With the PDU powered-on, users can access and control the host with a PC in the same LAN by connecting an RJ45 cable to the network port.

Interface Functions

Login Control Interface
Open the IE browser on any PC in LAN host and enter the IP address into the address bar: http://192.168.0.100. Log in to the Intelligent PDU control interface (shown below) by entering the administrator credentials that follow into the login screen:
User Name: admin
Password: admin

PDU System Information
Click System in the configuration bar on the left side of the interface to display PDU system information. The screen displays the following:

Power Port Control
Click Socket in the configuration bar on the left side of the interface. The screen displays the following:

Users can turn on or shut off any of the eight outputs through this interface.

Start all: click on the drop-down menu from the Operation box, choose “Start” and click the “Apply” button.
Shut off all: click the drop-down menu from the Operation box, choose “Shut off” and click the “Apply” button.
Custom Start and Shut off (e.g., the user wants to turn on outlets 1, 2, 3, and 4 but shut off 5, 6, 7, and 8): Click the empty boxes of the outlets to turn on, select Start from the drop-down menu and click Apply. Then, click the empty boxes of the outlets to turn off, select Shut off and click Apply.

ON and OFF Time Delay
Click PDU in the configuration box on the left side of the interface. The screen displays the following:

This function lets you adjust delay times in the start-up and shut-off sequences for connected equipment. In the default settings shown here, power is supplied to and shut off from all ports in one-second intervals after five seconds have passed from a start-up or shut-down command. Change values by entering them into the fields and click Apply. NOTE: When input power is disconnected from its source, the OFF Delay function is ignored, and power shuts off immediately to all equipment.
Shutting off the time-delay function only applies to the devices connected to the PDU.

Threshold Value Setting
Click Threshold value in the configuration box on the left side of the interface. The screen displays the following:

The meaning of each input is as follows; adjust values here and click Apply when finished:

Current Warning value (17.0 A) — if total current exceeds 17 A, the PDU will beep twice.
Current Overload value (17.0 A) — if total current exceeds 17 A, the PDU will shut off power to all output ports.
Warning Voltage value (250) — if input voltage exceeds 250 V, the PDU will beep twice.
Voltage Overload value (300) – if input voltage exceeds 300 V, the PDU will shut off power to all output ports.
Temperature is Under (5°C) or Above (50°C): if the built-in temperature sensor reads temperatures under or over these thresholds, the PDU will beep twice.
Humidity Warning value (80%): if the built-in humidity sensor reads humidity at more than 80%, the PDU will beep twice.
NOTE: if a threshold is reduced, the unit will not power off but will give a two-beep warning until the limit is exceeded.

Change the User Name and Password
Click User in the configuration box on the left side of the interface. The screen displays following:

After filling in the original and new user name as well as the password and password confirmation respectively, click the Apply button. The new user name and password will be used at the next login.

IP Address and DNS Setting
Click Network in the configuration box on the left side of the interface. The screen displays the following:
\

Users can adjust values here. The meaning of each input in the above dialog box is as follows:

Host Name: the name of the LAN.
IP Address: the current LAN IP address.
Subnet Mask: the current LAN subnet mask.
Gateway: the current gateway.
Enable DHCP: allows the supervising router to distribute network parameters automatically for the Intelligent PDU.
Primary DNS IP: refers to the supervising router setting of the current LAN.
Secondary DNS IP: refers to the supervising router setting of current LAN.

Additional Information

WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
DISPOSAL OF ELECTRIC AND ELECTRONIC EQUIPMENT
(Applicable In The European Union And Other European Countries With Separate Collection Systems)

This symbol on the product or its packaging means that this product must not be treated as unsorted household waste. In accordance with EU Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), this electrical product must be disposed of in accordance with the user’s local regulations for electrical or electronic waste. Please dispose of this product by returning it to your local point of sale or recycling pickup point in your municipality.

WARRANTY INFORMATIONintellinet-network.com

REGULATORY STATEMENTS FCC Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of Federal Communications Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and the receiver; connect the equipment to an outlet on a circuit different from the receiver; or consult the dealer or an experienced radio/TV technician for help.

CE
ENGLISH : This device complies with the requirements of CE 2014/30/EU (UKCA Electromagnetic Compatibility Regulations 2016) and / or 2014/35/EU (UKCA Electrical Equipment [Safety] Regulations 2016). The Declaration of Conformity for is available at: support.intellinet- network.com/barcode/163682