Davivy KE7201A Gooseneck Electric Kettle Instruction Manual

Instruction Manual
KE7201A

KE7201A Gooseneck Electric Kettle

SAFETY ADVICE

Basic safety measures should always be taken when using electrical appliances, including the following:

1. Read all instructions.
2. Some surfaces can become hot when in use, handle with care, and use the handle to carry.
3. To prevent fire or electric shock, do not immerse any part of the base or power cord in water or other liquids.
4. Do not leave this kettle unattended when in use, especially around children.
5. If not using or cleaning the kettle, the kettle shall be removed from the base, and cleaned or reinstalled after the equipment is cooled.
6. Never use the device if you discover damage, if water has entered the housing, or if the device has fallen.Never attempt to open or repair the device yourself. In case of malfunction, please only have it repaired by qualified experts! Contact an authorized retailer for this.
7. Device manufacturers do not recommend connecting devices with accessories, which may cause fire, electric shock, or personal injury.
8. For indoor use only.
9. Do not allow power cords to hang on the edge of a table or touch a heat source. Do not place appliances near hot gas or an electric stove or oven.
10. Before disconnecting, turn off the power switch and then unplug the cable.
11. The appliance should only be used to heat water, and other liquids should not be kept in the pot.
12. Burns may occur if the lid is opened during boiling or heating.

SPECIAL SECURITY INSTRUCTIONS

1. Store the instruction manual, warranty and receipt. If possible, please store them together with the inner box.
2. Only use cold water when filling.
3. The water level should not exceed a maximum of 0.8L or less than 0.5L. If the pot is too full, it will overflow when boiling.
4. Turn off the appliance before unplugging it.
5. The pot body is only used with the matching base.
6. Do not soak any part of the appliance in water.
7. If the power cord is damaged, it should be replaced by the manufacturer or other maintenance organization.
8. Pay attention to the steam ejected from the nozzle or hole on the cover, especially when refilling.
9. Be sure not to open the lid during heating to avoid scalding.
10. The equipment must be operated on a flat surface (such as kitchen cabinets and tea tables), do not be near gas stoves, ovens and other heat sources, and do not place it on the top of other electrical appliances.
11. The base and appearance of the equipment shall not become wet and shall be kept dry.
12. This device is not intended for use by children with intellectual disabilities, persons with sensory or mental disabilities, or persons lacking experience or knowledge, unless supervised or directed by a responsible safety supervisor.
13. Children should be supervised to ensure they do not play with the device.
14. The device should only be used in homes and similar situations and should not be used or placed outdoors.

PRODUCT PARTS NAME

A. SPOUT
B. LID
C. HANDLE
D. KETTLE BODY
E. POWER CORD
F. POWER BASE
G. FUNCTION BUTTON
H. TEMPERATURE INDICATOR

FUNCTION PANEL

1. Start/Stop/Temp Button: “Temperature Select/Start/Stop”.
2. Keep warm Button: “Keep Warm” .
3. 158℉ indicator lamp: warm water.
4. 176℉ indicator lamp: For making green tea.
5. 185℉ indicator lamp: For making coffee.
6. 194℉ indicator lamp: For making black tea.
7. 203℉ indicator lamp: For making herbal tea.
8. 212℉ indicator lamp: Boil water.

INSTRUCTIONS

1. Read the instructions carefully and keep it in a safe place before using it for the first time.
2. First fill the kettle with cold water to its maximum capacity of 0.8L, heat it to boiling, then pour away the water when the equipment is completely cooled, repeat several times if necessary to remove the odor before normal use.
   Note: Use only water, no additives or ingredients!

BOIL WATER

1. Assemble the kettle and the base together on a smooth and dry surface (tea table, table top or kitchen cabinet), then plug in the kettle, open the stainless steel lid, and fill with enough cold water, the water level with the scale inside the kettle, between 0.5L and 0.8L.
   Please note: Do not fill the kettle with liquids other than water!
   It will never burn out the kettle, and will not boil water for a long time to dry it. When the water capacity is less than 0.5L, the water will boil before the temperature reaches the set temperature. In this case, the temperature controller will automatically close the program to ensure that the kettle will not be burnt out, and you can refill the water after the equipment is completely cooled down.

2. Put the lid on and make sure it fits in place.

3. Put the kettle on the base.

4. Check whether the voltage is the same as the voltage of the appliance (details can be found on the base rating label).

5. Only connect the machine to properly installed 120V/ 60Hz safety sockets.

6. Plug in the plug and press the Start/Stop/Temp button, the boiling water indicator (212℉) will come on. If no other operation is performed, the kettle will Start heating after 3 seconds. When the water is boiling, the indicator will “beep” and turn off the power.

FUNCTIONAL SPECIFICATION:

• Start and re-selection function: During the heating process of the kettle, you can also press “Start/Stop/Temp” to select another temperature, and the kettle will execute the new command and boil water at the newly selected temperature. When the water temperature is heated to the selected temperature, there will be a prompt sound (0.2 seconds), and the button light will turn off. The temperature light will turn off 20 seconds later (if the heat preservation function is set, the heat preservation light will flash).
• Off-seat protection function: when the body is lifted from the base during heating, the kettle will stop working. If the kettle is not put into the base, press the “on/off” key to select the temperature, but it will not start the program. After staying for 3 seconds, a prompt sound (0.2 seconds) will automatically exit the program (all lights are off ).
• Anti-freeze function: Press the “Keep warm” button alone to start the kettle heating and automatic heat preservation (212℉ boiling water has no heat preservation function, press the “Keep warm” button is invalid).
• Memory function when the power is off: After lifting the kettle body in the heat preservation state (less than 1 minute) and then putting it back to the base, it can still keep the heat preservation.
• Over-temperature protection function: when the water temperature in the pot is greater than or equal to the current set temperature, pressing the “start” button will not start the heating, and there will be three beeps/0.2 seconds at the same time. When the water temperature in the pot is greater than or equal to the current set temperature, press the “Keep Warm” button to keep warm, (the “Start” button will not light up and will not heat up), when the water temperature drops to the set temperature (about minus 2 degrees) ) will start the hot filling and maintain a constant temperature until the end of the 2-hour holding time.
• Stop heating or exit heat preservation: Press and hold the “switch” button for 2 seconds during the heating process of the kettle (beep once/0.2 seconds) to exit the program, and all lights will go out (short press will jump to the next temperature). After the program starts, press the “Keep Warm” button (the keep warm light is on, and a beep sound/0.2 seconds), that is, the keep warm function is set (2 hours according to the menu temperature); press the “Keep Warm button” or “Switch” key to exit keep warm.
• Turn off or turn on the prompt sound: long press the “Keep Warm” button for 3 seconds to turn off (or turn on) the prompt sound, and the prompt sound is on by default.

Temperature Setting

1. Press the “Start/Stop/Temp” button, the default temperature is 212℉. Then press the “Start /Stop/Temp” button, the indicator will change from 158℉-176℉-185℉-194℉-203℉-212℉.
2. After the temperature is set, the indicator stays at the temperature point for 3 seconds, and the heating starts after 1 prompt sound.
3. When the temperature is 158℉, 176℉, 185℉, 194℉, 203℉, it has 2 hours of heat preservation function (but must press the “Keep warm” button, the button light is effective).

Other Precautions

1. In order to avoid the actual temperature being higher than the set temperature, at 40 ℉ before the set temperature, the system will change to point heating: heating for 2 seconds /stopping for 2 seconds until the temperature gradually rises to the set temperature, then stopping heating.
2. After the kettle stops working, please disconnect the kettle from the power supply and do not open the lid when pouring water. To avoid burns, wait at least 5 seconds after opening the lid before putting it back on.

How to Clean

• Unplug the kettle and let it cool.
  Note: Do not immerse the kettle, power cord or plug in water！

• It is allowed to clean the external surface of the kettle, which can be wiped with a cloth of slightly wet water. Do not add any additives.

• Do not use a sander, which can damage the surface of the product and may cause electric shock.

• The kettle should be thoroughly dried after cleaning and kept dry.

Scale Removal

Note: long-term use will have mineral precipitation, this is not a product quality problem.

• Hard water can allow minerals to build up inside the kettle. To avoid this, use drinking water.
• Add baking soda, acid scale remover or other standard scale remover and boil water several times to clean the kettle. The water level should not exceed MAX.

WARRANTY INFORMATION

1. The manufacturer shall provide a guarantee in accordance with the laws and regulations of the customer’s country for at least 1 year from the date when the equipment is sold to the end user, and the guarantee only includes defects in materials or workmanship.
2. Repairs within the warranty period can only be carried out by authorized service centers, and the original bill at the time of purchase (date of purchase) must be provided when warranty claims are made for quality.
3. Warranty period not applicable：
   • Normal Age Wear;
   •  Improper use, e.g. overloading of equipment, use of unapproved accessories;
   •  Use of force, damage caused by an external influence;
   •  Damage caused by failure to comply with the user’s manual, e.g. use of inappropriate voltage power supply or connected equipment that does not conform to installation instructions;
   •  Electrical appliances that have been partially or completely disassembled.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>