Westinghouse 52220 Linear Ballast Bypass LED Light Bulb User Manual
- June 3, 2024
- Westinghouse
Table of Contents
52220 Linear Ballast Bypass LED Light
Bulb
User Manual
Product Features:
UL certified
Full glass housing: No Aging, Yellowing, Bending
Designed to work without a ballast
Product Applications:
Widely used in residential buildings, oces, shopping malls, supermarkets, hosptials, assembly lines, warehouses, etc. for energy saving illumination.
Installation Instructions:
Please follow all this instructions and notes, to ensure the product is installed and used in a safe manner.
Safety Precautions:
For your and others safety please read the precaution carefully before
installation:
- Product should be installed by a qualied electrician.
- Switch the power supply before commencing work, make sure all connections are secure before you power on.
- Do not use an LED driver with this product.
- NOT FOR USE WITH EMERGENCY LIGHTING.
Wiring Instructions – Electronic Ballast
Retrofit luminaire with 1 lamp
Retrofit luminaire with 2 lamps
Retrofit luminaire with 3 lamps
DIMMING FUNCTION
This tube can be achieve 0-10V dimming when installed in combination with
dimming module (Westinghouse
Lighting model 502606930). One dimming module can only operate one LED
tube.
WARNING:
Only use the control provided with or specified by these instructions to
control this lamp. This lamp will not operate properly when connected to a
standard (incandescent) dimmer or dimming control. Only operate with specific
dimming module 502606930 manufactured by Westinghouse.
Type B LAMP – intended for operation in luminaires with traditional
fluorescent-type lamp holders wired directly to the branch circuit. This
includes both factory-wired luminaries as well as those converted for this
purpose under a retrofit program.
WARNING – Risk of fire or electric shock. LED Retrofit Kit installation
requires knowledge of luminaire electrical systems. If not qualified, do not
attempt installation. Contact a qualified electrician.
WARNING – Install this kit only in the luminaires that have the
construction features and dimensions shown in the photographs and/or drawings
and where the input rating of the retrofit kit does not exceed the input
rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to
edges of sheet metal or other sharp objects.
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING
JURISDICTION.
Do not make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
Installers should not disconnect existing wires from lampholder terminals to
make new connections at lampholder terminals. Instead installers should cut
existing lampholder leads away from the lampholder and make new electrical
connections to lampholder lead wires by employing applicable connectors.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The units covered by this report were intended to retrot surface mount without
diuser, Type IC or non-IC recessed mount Listed uorescent luminaires that use
maximum three tubular lamps, the minimum lamp compartment dimensions are
listed below:
Model| MINIMUM LAMP COMPARTMENT DIMENSIONS
[Length x Width x Height][mm]
---|---
52220| 620 x 600 x 80
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
Used under license by Westinghouse Lighting.
www.westinghouselighting.com
All Rights Reserved.
Westinghouse are trademarks of Westinghouse Electric Corporation.
Made in China
Documents / Resources
|
Westinghouse 52220 Linear Ballast Bypass LED Light
Bulb
[pdf] User Manual
52220, Linear Ballast Bypass LED Light Bulb, 52220 Linear Ballast Bypass LED
Light Bulb, Ballast Bypass LED Light Bulb, Bypass LED Light Bulb, LED Light
Bulb
---|---