Westinghouse W-761 042822 Indoor Lighting Fixture Owner’s Manual
- June 3, 2024
- Westinghouse
Table of Contents
Westinghouse W-761 042822 Indoor Lighting Fixture
FIXTURE WARRANTY
This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period of five years from the purchase date. This warranty is in lieu of all other warranties expressed or implied. This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration of components, nor does it cover damages caused through abuse, improver installation, surges in electric current, or acts of third parties. This warranty does not cover the costs of removing and re-installing the lighting fixture. If this product fails for any reason covered by this warranty, please contact us at www.westinghouselighting.com/contact- us.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed
to give you many
years of beauty and service. For questions and comments, please visit
www.westinghouselighting.com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are
included before discarding any pack- ing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do
not proceed. Contact a qualified electrician. Read all instructions before
beginning. Proper wiring is essential for safe operation of this fixture. When
cutting or drilling into walls or ceilings, do not damage electrical wiring,
gas lines, or water lines. If any of the fixture or wiring components are
damaged, do not install fixture. Return to place of purchase. For fixtures
provided with 75° C or 90° C supply wire warning only. (These warnings are
provided on the U.L. label and on the fixture carton.) Risk of fire. Most
dwellings built before 1985 have supply wires rated 60° C. Consult a qualified
electrician before installing.
CHANDELIER MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.
- Turn off power at fuse box to avoid possible electric shock.
- Thread mounting screws (A) into cross bar (B) approximately 1/4 inch (see fig. 1).
- Secure cross bar (B) to outlet box (C) with outlet box screws (D) (if applicable).
- Select the number of stems (E) to install based on desired fixture length, then connect stems (E) If applicable.
- Thread fixture wires up through stem(s) (E), coupling (F), and canopy (G) (If applicable).
- Thread stem(s) (E) into socket assembly (H) and into coupling (F) (If applicable).
- Identify color coding of fixture wires (see figure 2).
- Connect the black wire from the fixture with the black wire (live wire) from the outlet box by wire connector (I), and wrap the wire connector (I) with electrical tape for a more secure connection.
- Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box by wire connector (I), and wrap the wire connector (I) with electrical tape for a more secure connection.
- Partially thread green grounding screw (J) into side hole (K) on cross bar (B) (see figure 1).
- Wrap grounding wire from fixture around green grounding screw stem (J) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box by wire connector (I) (if applicable), then wrap the wire connector (I) with electrical tape for a more secure connection.
- Tighten grounding screw (J). Do not over tighten.
- Tuck wires inside outlet box (C) (see figure 1).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
- Raise canopy (G) to ceiling, allowing mounting screws (A) to protrude through openings in canopy (G), and secure into place with cap nuts (L) (see fig. 1).
- Secure the decorative frame (O) to the arms (M) by cap nuts (N).
- Install lamp(s). Do not exceed the recommended wattage.
- Turn power back on at circuit box.
SEMI-FLUSH MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have
ground wires. These fixtures meet all UL specifications.
-
Turn off power at fuse box to avoid possible electric shock.
-
Thread mounting screws (A) into cross bar (B) approximately 1/4 inch (see fig. 1).
-
Secure cross bar (B) to outlet box (C) with outlet box screws (D) (if applicable).
-
Loose the set screw (P) and remove the thread nipple (Q) from the coupling (F).
-
Thread fixture wires up through coupling (F) and canopy (G). And thread the coupling (F) into socket assembly (H). (carefully twist fixture coupling (F) and canopy (G) to socket assembly (H). Do not twist or kink wires)
-
Tighten the set screw (P).
-
Identify color coding of fixture wires (see figure 2).
-
Connect the black wire from the fixture with the black wire (live wire) from the outlet box by wire
connector (I), and wrap the wire connector (I) with electrical tape for a more secure connection. -
Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box by wire connector (I), and wrap the wire connector (I) with electrical tape for a more secure connection.
-
Partially thread green grounding screw (J) into side hole (K) on crossbar (B) (see figure 1).
-
Wrap the grounding wire from fixture around the green grounding screw stem (J) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box by wire connector (I) (if applicable), then wrap the wire connector (I) with electrical tape for a more secure connection.
-
Tighten the grounding screw (J). Do not over-tighten.
-
Tuck wires inside outlet box (C) (see figure 1).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
- Raise canopy (G) to ceiling, allowing mounting screws (A) to protrude through openings in canopy (G), and secure into place with cap nuts (L) (see fig. 1).
- Secure the decorative frame (O) to the arms (M) by cap nuts (N).
- Install lamp(s). Do not exceed the recommended wattage.
- Turn power back on at circuit box.
WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be
safely supported.
CLEANING AND CARE
To clean, wipe the fixture with soft cloth. Clean glass with mild soap.
Spraying from chemical cleaners can discolor the finish of the fixture. Do not
use scouring pads, powders, steel wool or abrasive paper to clean this
fixture.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are
needed. Available parts can be ordered from the place of purchase. Use exact
wording from diagrams when ordering parts.
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
and Westinghouse are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting. All Rights Reserved. Made in
China
References
- Sustainable LED lighting solutions | Philips lighting
- Ceiling Fans | Lighting Fixtures | Lamps
- Contact Us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>