Alphacool Eisbaer AiO CPU Digital Water Cooler Instruction Manual

June 3, 2024
ALPHACOOL

Eisbaer AiO CPU Digital Water Cooler
Instruction ManualAlphacool Eisbaer AiO CPU Digital Water
Cooler

SAFETY INSTRUCTIONS

READ THE SAFETY INSTRUCTIONS BEFORE STARTING THE INSTALLATION.

  • Not suitable for children under 6 years. (contains small parts which could be swallowed).

  • Do not run any cooling components without ensuring that cooling liquid is flowing through the cooling system. Coolers operated without coolant can become very hot.  Caution: Burn Hazard!

  • Coolers that have no coolant flowing through them can destroy the computer hardware. When switching on the hardware, always make sure that the pump
    is working.

  • Please note when tightening the connectors or fittings, no tools such as screwdrivers, pliers, or wrenches should be used. All plastic products or metal threaded  connections, which are linked with plastic parts, are easily over-loaded with tools. Cracking or other damages incurred in this way, as well as damage from leaking coolant, are not covered under the warranty!

  • Use only connectors with a sealing o-ring. When using a sealing ring a firm tightening with the hand is enough. Your instruction manual will clearly refer to
    the use of tools in exceptional cases.

  • If you have not done so yet, please check your hardware and cooling system (tightness, pump function and fans). This will minimize time spent searching for possible  problems. ALPHACOOL INTERNATIONAL GMBH accepts no liability on the warranty of the manufacturer of the electronic components. The assembly of the  cooling system takes place at your own risk.

  • The screws should not be tightened too firmly. If you tighten the screws excessively, the knurled nuts can loosen and the cooler´s uniform pressure is no
    longer guaranteed.

  • Fasten the connections of your choice to the cooler. Do not use tools such as wrenches for fastening the connections. Connectors with 8mm long threads
    may stop the flow.

  • We recommend a tightness test before assembling/installing the cooler. The water pressure in the water cooling loop can be at a maximum of 0.8 bar. DO NOT use  tools on the connectors.

  • Ensure that the cooler is touching all components to be cooled through thermal grease and thermal pads.

  • Only use distilled water or ALPHACOOL CAPE KELVIN CATCHER in your cooling circuit. Damage caused by unsuitable coolant is not covered by the warranty!

Specified normal operation
All ALPHACOOL INTERNATIONAL GMBH cooling components are constructed and licensed for ALPHACOOL INTERNATIONAL GMBH computer construction
parts. The warranty expires in case of misuse.

Warranty

  1. Data, designs, illustrations, technical data, weight, measurement and specifications, contained in folders, catalogues, circulars, announcements or price lists, have a purely  informative character. We do not undertake warranty for the correctness of these data. As to the kind and the range of delivery, the data contained in the order and  confirmation of order alone are decisive.

  2. If there is a lack of warrantor, you are entitled, on the basis of the legal regulations to require subsequent delivery, to withdraw from the contract or reduce the purchase  price. If you are a consumer, the limitation period of warranty claims for the supplied commodity amounts to two years starting from receipt of goods (§ 13 BGB). If you  are an entrepreneur, in accordance with legal conditions the limitation period amounts to only one year (§ 14 BGB).

  3. The warranty claim is valid only in combination with the original invoice, the sales slip or an ALPHACOOL confirmation on warranty claim.

  4. It is ALPHACOOL INTERNATIONAL GMBHs own discretionary authority to replace or repair the defective product or defective component. The replaced product  or component changes into property of ALPHACOOL INTERNATIONAL GMBH.

  5. All warranty claims are accomplished by ALPHACOOL INTERNATIONAL GMBH or its authorized dealers. If the repair is carried out by a non-authorized or assigned person, ALPHACOOL INTERNATIONAL GMBH does not take over either costs or liability, unless the repair has been previously agreed upon with ALPHACOOL INTERNATIONAL GMBH.

  6. All costs resulting from refitting of the products are not taken over by ALPHACOOL INTERNATIONAL GMBH.

  7. ALPHACOOL INTERNATIONAL GMBHs warranty excludes the following points:
    7.1. Regular controls maintenance and repair or the replacement of parts subject to regular wear and tear.
    7.2. Improper manipulation or defects caused by incorrect installation.
    7.3. Damages caused by storm, water, fire, overvoltage, acts of God, war, incorrect connection to the net, insufficient or incorrect ventilation or other reasons over which  ALPHACOOL INTERNATIONAL GMBH has no influence.
    7.4. Damages resulting from transportation or improper packaging.

  8. Consumer´s rights are valid in the respective country; demands made to the salesman, as explained and laid down in the sales contract, will not be covered by this  warranty. ALPHACOOL INTERNATIONAL GMBH, its Branch Office and Distributors, are not responsible for direct or indirect damage or losses, as far as the compelling legal regulations do not oppose it.

  9. ALPHACOOL INTERNATIONAL GMBH does not take over the warranty of the manufacturer of the electronic construction units and components. The assembly of  the cooler takes place at your own risk.

Contact an authorized waste management company in your country. A waste removal with the municipal waste (unsorted garbage) or similar mechanisms for the collection of  local wastes is not permissible!

MOUNTING MATERIAL

Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
1

TECHNICAL DETAILS

COOLER Eisbaer
AMD: AM5 / AM4 / AM3+ / AM3
INTEL: 2011 / 2011-3 / 2066 / 1156 / 1155 / 1151 / 1150 / 1200 / 1700
Mounting kits for TR4 (Art. No.: 12875) & 2011-3 Narrow ILM (Art. No.: 12531) are available separately. Alphacool Eisbaer AiO CPU Digital Water
Cooler - Figure 2

PUMP DC-LT 2
Power consumption: 4 W
Voltage: 12 V DC
Maximum flow rate: 75 l / h
Maximum head: 0,95 m
Power connector: 3-Pin

RADIATORS

NexXxos Series
Material: Copper
Model variants:| XT45 120
dimension: 160 mm x 124 mm x 45 mm
ST30 140
dimension: 178 mm x 144 mm x 30 mm
ST30 240
dimension: 278 mm x 124 mm x 30 mm
ST30 280
dimension: 316 mm x 144 mm x 30 mm
ST30 360
dimension: 397 mm x 124 mm x 30 mm
ST30 420
dimension: 459 mm x 144 mm x 30 mma
---|---

QUICK COUPLING
Compatibility: 11/8 mm tubes
Material: NylonAlphacool Eisbaer AiO CPU Digital Water Cooler - Figure
3

MOUNTING THE RADIATOR

PUSHING FANSAlphacool Eisbaer AiO CPU Digital Water Cooler - Figure
4

SUCKING FANSAlphacool Eisbaer AiO CPU Digital Water Cooler - Figure
5

PREPARATION CPU

  • Remove the protective film from the cooling plate.

  • Remove any remaining thermal paste from the CPU.

  • Apply a pea-sized blob of thermal paste to the center of the CPU.

  • Spread the paste using a spatula, or similar to an even, thin layer (< 0.5 mm layer thickness).
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
7

  • Remove the protective film from the adhesive strips of the included backplate. Please note the correct alignment of the backplate:
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
8

CPU COOLER ASSEMBLY

INTEL 1156 / 1155 / 1151 / 1150 / 1200 / 1700

  • Select the appropriate bracket and screws.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
9

  • Plug the bracket together as shown.

  • Slide the compression springs and washers onto the screws and fix them to the bracket.

  • Remove any remaining thermal paste from the CPU.

1156 / 1155 / 1151 / 1150 / 1200

Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
10

1700Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
11

  • Attach the cooler to the socket using the backplate. Tighten the screws crosswise, handtight.
  • Make sure that the window is facing upwards (or that the Alphacool logo can be read from the front). This design ensures that the pump does not run dry.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
12

INTEL 2011 / 2011-3 / 2066

  • Select the appropriate bracket and screws.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
13

  • Plug the bracket together as shown.

  • Slide the compression springs and washers onto the screws and fix them to the bracket.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
14

  • Attach the cooler to the socket as shown. Tighten the screws crosswise, hand-tight.

  • Make sure that the window is facing upwards (or that the Alphacool logo can be read from the front). This design ensures that the pump does not run dry.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
15

Note: Some 2011/- 3 Socket motherboards have continuous threaded mounting holes in the base. In this case, do not tighten the screws more than 4 mm.

AMD AM3+ / AM3

  • Select the appropriate bracket and screws.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
16

  • Plug the bracket together as shown.

  • Slide the compression springs and washers onto the screws and fix them to the bracket.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
17

  • For the mounting on the socket you need the original backplate of the mainboard.

  • Attach the cooler to the socket as shown. Tighten the screws crosswise hand-tight.

  • Make sure that the window is facing upwards (or that the Alphacool logo can be read from the front). This design ensures that the pump does not run dry.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
18

AMD AM4/AM5

  • Select the appropriate bracket and screws.Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure 19

  • Plug the bracket together as shown.

  • Slide the compression springs and two different washers onto the screws and fix them to the bracket.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
20

  • For the mounting on the socket you need the original backplate of the mainboard.

  • Attach the cooler to the socket as shown. Tighten the screws crosswise hand-tight.

  • Make sure that the window is facing upwards (or that the Alphacool logo can be read from the front). This design ensures that the pump does not run dry.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
21

CONNECTING FANS & PUMP

  • Connect the fan cables with the included PWM adapter.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
22

  • Connect the PWM adapter and the 3-pin connector of the pump to your mainboard.
    Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
23

INITIAL START-UP

If your Eisbaer AiO is unusually loud during initial operation, tipping the entire PC case back and forth a little can help. The higher volume level of the pump occurs due to  air bubbles in the closed system. These bubbles form during transport or due to movement during installation.
Double-check that the radiator is mounted above the water block. This setup helps deaerate the system.
After around 12 hours of operation any air in the system should be eliminated and the pump should run quietly as usual.

USING QUICK RELEASE CONNECTORS

The pre-installed quick-release fastener offers the possibility of expanding the Eisbaer loop quickly and easily. The connector is compatible with many other products from  our range. Attention: 2 – 3 drops of water can escape when unscrewing the quick release mechanism – This is normal. Alphacool
Eisbaer AiO CPU Digital Water Cooler - Figure 24

FILLING UP COOLANT

The Eisbaer All-in-One is prefilled and normally it is not necessary to top up the coolant. If you want to expand your circuit, e.g. with a GPX Eiswolf graphics card cooler, it  is advisable to check the water level. If the pump is running unsusually loud, liquid should be topped up urgently. We only recommend clear coolants from our own  production (CKC or Eiswasser Crystal – no UV!) or pure distilled or osmosis filtered water.
A fillport on the cooler is provided for filling. We recommend using a funnel or a filling bottle:

Alphacool Eisbaer AiO CPU Digital Water Cooler - Figure
25

Imprint:
Alphacool International GmbH
Marienberger Str. 1
38122 Braunschweig
Germany
Support: +49 (0) 531 28874 – 0
Fax: +49 (0) 531 28874 – 22
E-Mail: info@alphacool.com https://www.alphacool.com
General Manager: Fabian Noelte
WEEE-Reg.-Nr.: DE 54464644
Trade Register: Amtsgericht Braunschweig HRB 202390
VAT.ID.Nr.: DE270458421
Tax number: 13/207/02047

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ALPHACOOL User Manuals

Related Manuals