Alphacool 15486 Core Flat Reservoir User Guide
- May 15, 2024
- ALPHACOOL
Table of Contents
Alphacool 15486 Core Flat Reservoir
Specifications
- 1x 240 or 360 Flat Reservoir
- 1x O-Ring*
- 1x VPP-D5 Pump*
- 1x Allen Key
- 4x M4x22 Pump Screw
- 1x Core Push Mount Set
- 4x G1/4 Plug
- 1x ARGB Adapter
- 1x Plug tool
Product Usage Instructions
Pump Installation
- To install the pump, insert the O-Ring and tighten the screws with 1.5Nm.
Functionality of the Push Pins
- The Push Pins are used for mounting the reservoir. They provide a secure attachment to either a radiator or a panel.
Push Pin Mounting
- With Radiator: Use screws with the appropriate thread for your radiator to securely mount the reservoir.
- With Panel: Securely attach the reservoir to a panel using the Push Pins.
Inlet and Outlet configuration
- Configure the inlet and outlet connections as needed for your setup.
Connect ARGB Lighting
- If applicable, connect the ARGB lighting to enhance the visual appeal of your reservoir.
Connection Pump Cable
- Ensure the pump cable is properly connected for the pump to function correctly.
Filling and Ventilation
- Properly fill the reservoir and ensure proper ventilation to avoid air bubbles in the system.
Dimensions
- The dimensions of the reservoir are provided in millimeters for reference.
FAQ
Need Help?
- If you require assistance with your Alphacool Core Flat Reservoir, you can contact Alphacool International GmbH at: Marienberger Str. 1, D-38122 Braunschweig, Germany
- Support: +49 (0) 531 28874-0
- Fax: +49 (0) 531 28874 – 22
- Email: info@alphacool.com
- Visit their website at alphacool.com
Accessories
INSTALLATION INSTRUCTION
Pump installation: Insert O-Ring
Pump installation
- Tighten the screws with 1.5Nm.
Functionality of the Push Pins
Push Pin mounting: With radiator
- Use the screws with the appropriate thread for your radiator.
Push Pin mounting: With Panel
Configuration inlet and outlet
Alphacool Core Flat Reservoir 360 Left D5/VPP
Alphacool Core Flat Reservoir 240 Left D5/VPP
Connect ARGB lighting
Connection pump cable
Filling and ventilation
- Fill the reservoir with suitable coolant.
- We recommend using only our products for this purpose.
- To remove trapped air from the reservoir, sway the reservoir back and forth a little and then open a suitable port so that the air bubbles can escape from the device.
- When swinging, make sure that all openings are closed or in use except for the ventilation opening.
- If necessary, coolant must be topped up. Then switch on the pump so that the water is distributed in the circuit.
- Switch the pump off again and repeat the process until all the air escapes from the reservoir.
Dimensions in millimeter (mm)
- Alphacool Core Flat Reservoir 360 Left D5/VPP
- Alphacool Core Flat Reservoir 240 Left D5/VPP
Need help?
- Alphacool International GmbH Marienberger Str. 1
- D-38122 Braunschweig Germany
- Support: +49 (0) 531 28874-0
- Fax: +49 (0) 531 28874 – 22
- E-Mail:info@alphacool.com
- https://www.alphacool.com
Documents / Resources
|
Alphacool 15486 Core Flat
Reservoir
[pdf] User Guide
15486 Core Flat Reservoir, 15486, Core Flat Reservoir, Flat Reservoir
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>