Alphacool Core Eisblock Aurora RTX-N 3090 Ti Suprim X INCL Bakplate Installation Guide
- June 9, 2024
- ALPHACOOL
Table of Contents
Alphacool
CORE EISBLOCK AURORA RTX-N 3090 TI SUPRIM X INCL. BACKPLATE Read the
safety instructions before starting the installation.
Safety instructionhttps://www.alphacool.com/download/SAFETY%20INSTRUCTIONS.pdf
Accessories
Compatability check
Before starting the cooler assembly, compare your card with the pictures in
our configurator. To do so, visit https://www.hwconfig.com and search for
your graphics card or cooler model. For a definitive identification, you can
also compare the PCB number. The cooler was designed for a special PCB layout.
Occasionally, graphics card manufacturers may revise the design of their card
slightly, causing the cooler not to fit on later models. During assembly,
please make sure taller parts have enough space around them and that the
cooler does not damage your graphics card.
Alphacool International GmbH is not liable for assembly errors occurring due
to negligence, such as selecting an incompatible cooler.
Prepare graphics card
Put the hardware on an antistatic mat. Begin dismantling the original cooler. Depending on the structure of the cooler, remove the screws at the back of the card and carefully unhook the fan connector first. If the original cooler uses thermal glue, extreme care should be taken as you can easily damage parts. Pick up all the items carefully. Next, clean the hardware of thermal paste or pad residues with a solvent (e.g. isopropanol alcohol).
Mounting the IO shield
Attach the slot cover as shown using the 2 M3x5 screws and M3 nuts.
Mounting the front pads
Clean the contact surfaces on the bottom side of the cooler with alcohol or
similar. The surface must be free of contaminants.
Remove the protective foils from the thermal pads and place the pads on the
copper block as shown.
Applying thermal paste
With the help of a plastic strip or similar spread a thin layer of thermal paste on the GPU. The layer should be less than a millimeter thick, otherwise the surrounding components may be contaminated.
Mounting the graphics card
Place the graphics card on the prepared cooler. Fasten the card as shown with the 6 M2x5 screws with M2 washers. Hand-tighten the screws crosswise, one turn at a time.
Mounting the backpads
Remove the protective foils from the thermal pads and place the pads on the
PCB as shown.
Mounting the backplate
Put the backplate on and screw it together with the 9 M2x11 screws as shown.
Connecting the LED
To control the digital – RGB lighting, connect the included adapter to the 3 –
pin female connector and plug it to a digital – RGB controller (e.g.
Alphacool Aurora Eiscontrol, Art.: 15360, not included). You can connect
additional digital RGB LEDs to the remaining 3 – pin male connector.
Close the inlets which you do not need for tubing.
Screw in the screw plugs with the enclosed tool.
Alphacool International GmbH Marienberger Str. 1
D-38122 Braunschweig Germany
Support: +49 (0) 531 28874 – 0
Fax: +49 (0) 531 28874 – 22
E-mail: info@alphacool.com
https://www.alphacool.com
V.1.00-04.2022
Documents / Resources
| OC
Alphacool Core Eisblock Aurora RTX-N 3090 Ti Suprim X INCL
Bakplate
[pdf] Installation Guide
Alphacool Core Eisblock Aurora RTX-N 3090 Ti Suprim X INCL Bakplate, Alphacool
Core Eisblock Aurora RTX-N 3090 Ti Bakplate, Suprim X INCL Bakplate, Aurora
RTX-N 3090 Ti Bakplate, RTX-N 3090 Ti Bakplate, Bakplate
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>