ALPHACOOL EISBLOCK XPX CPU Water Cooler Instruction Manual

: June 4, 2024
: ALPHACOOL

Table of Contents

ACCESSORIES
COMPATIBILITY CHECK
PREPARE GRAPHICS CARD
Documents / Resources

ALPHACOOL EISBLOCK AURORA GPX-N ACRYL
**ACTIVE BACKPLATE 3080 / 3090 GAMING / EAGLE

**

Read the safety instructions before starting the installation.

ALPHACOOL EISBLOCK XPX CPU Water Cooler - qr code https://www.alphacool.com/download/SAFETY%20INSTRUCTIONS.pdf

ACCESSORIES

COMPATIBILITY CHECK

Before starting the cooler assembly, compare your card with the pictures in our configurator. To do so, visit https://www.hwconfig.com and search for your graphics card or cooler model. For a definitive identification, you can also compare the PCB number. The cooler was designed for a special PCB layout. Occasionally, graphics card manufacturers may revise the design of their cards slightly, causing the cooler not to fit on later models. During assembly, please make sure taller parts have enough space around them and that the cooler does not damage your graphics card.
Alphacool International GmbH is not liable for assembly errors occurring due to negligence, such as selecting an incompatible cooler.

PREPARE GRAPHICS CARD

Put the hardware on an antistatic mat. Begin dismantling the original cooler. Depending on the structure of the cooler, remove the screws at the back of the card and carefully unhook the fan connector first. If the original cooler uses thermal glue, extreme care should be taken as you can easily damage parts. Pick up all the items carefully. Next, clean the hardware of thermal paste or pad residues with a solvent (e.g. isopropanol alcohol).

ALPHACOOL EISBLOCK XPX CPU Water Cooler - 1

Clean the contact surfaces on the bottom side of the cooler with Isopropanol alcohol or similar. The surface must be free of contaminants.
Remove the protective foils from the thermal pads and place the pads on the backplate as shown.
Please note:
Pad No. 5 (8x74x3mm) must be shortened to 66mm (8x66x3mm) as shown.
NOTE
If you use the Active Back late for the 3080, use the pads of the original Alphacool graphics card cooler. You need the pads (see above)
No.1 (15x15xlmm),
No.2 (15x5lx1mm) and
No.3 (15x38x1 mm) = 2liyallidiam and for
No.4 (30x30x2mm) = 3mm thickness.

ALPHACOOL EISBLOCK XPX CPU Water Cooler - 4

Put the active backplate on and screw it together with the 6 M2x11 screws as shown.

ALPHACOOL EISBLOCK XPX CPU Water Cooler - 2

To control the digital RGB lighting, connect the 3-pin female connector to the 3-pin male connector of the graphics card LED. You can connect additional digital RGB LEDs to the remaining 3-pin male connector. As shown, you have two installation options.

ALPHACOOL EISBLOCK XPX CPU Water Cooler - 3

Two options are available to connect the unit to the water circuit. Use either the two G1/4″ threads or the 5/3mm connections in conjunction with the optionally available CX
distributor with article number 13041.

Alphacool International GmbH
Marienberger Str. 1
D-38122 Braunschweig
Germany
Support: +49 (0) 531 28874 – 0
Fax: +49 (0) 531 28874 – 22
E-Mail: info@alphacool.com
https://www.alphacool.com
General Managers: Andreas Rudnicki, Nathanael Draht, Fabian Noelte
WEEE-Reg.-Nr.: DE 54464644
Trade Register: Amtsgericht Braunschweig HRB 202390
VAT.ID.Nr.: DE270458421
Tax number: 13/207/02047

Documents / Resources

| ALPHACOOL EISBLOCK XPX CPU Water Cooler [pdf] Instruction Manual
EISBLOCK, XPX CPU Water Cooler, CPU Water Cooler, Water Cooler, EISBLOCK, Cooler
---|---