ALPHACOOL Eisblock ES Acetal GPX-N RTX 3080/3090 Turbo with Backplate User Manual
- June 3, 2024
- ALPHACOOL
Table of Contents
ALPHACOOL Eisblock ES Acetal GPX-N RTX 3080/3090 Turbo with Backplate
Instruction
Read the safety instructions before starting the installation.
ACCESSORIES
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
---|---|---|---|---|---|---|---|
1x 8x77x1mm | 2x 15x51x1mm | 1x 15x38x1mm | 1x 15x15x1mm | 1x 8x84x1mm | 1x | ||
8x77x3mm | 1x 8x84x3mm | 2x 30x30x3mm | |||||
9 | 10 | 11 | 12 | 13 | 14 | 15 | |
2x 15x51x3mm | 1x 15x38x3mm | 1x 15x15x3mm | 2x 15x51x2mm | 1x 15x38x2mm | 1x | ||
15x15x2mm | 1x 30x30x2mm | ||||||
2x M3x5 screws | 2x M3 | ||||||
nuts | 4x M2x5 | ||||||
screws | 4x M2 | ||||||
washers | 8x M2x11 | ||||||
screws | 1x Thermal grease |
COMPATIBILITY CHECK
Before starting the cooler assembly, compare your card with the pictures in
our configurator. To do so, visit https://www.hwconfig.com and search for
your graphics card or cooler model. For a definitive identification, you can
also compare the PCB number. The cooler was designed for a special PCB layout.
Occasionally, graphics card manufacturers may revise the design of their card
slightly, causing the cooler not to fit on later models. During assembly,
please make sure taller parts have enough space around them and that the
cooler does not damage your graphics card.
Alphacool International GmbH is not liable for assembly errors occurring due
to negligence, such as selecting an incompatible cooler.
PREPARE GRAPHICS CARD
Put the hardware on an antistatic mat. Begin dismantling the original cooler. Depending on the structure of the cooler, remove the screws at the back of the card and carefully unhook the fan connector first. If the original cooler uses thermal glue, extreme care should be taken as you can easily damage parts. Pick up all the items carefully. Next, clean the hardware of thermal paste or pad residues with a solvent (e.g. isopropanol alcohol).
-
Attach the slot cover as shown using the 2 M3x5 screws and M3 nuts.
-
Clean the contact surfaces on the bottom side of the cooler with alcohol or similar. The surface must be free of contaminants. Remove the protective foils from the thermal pads and place the pads on the copper block as shown.
-
With the help of a plastic strip or similar spread a thin layer of thermal paste on the GPU. The layer should be less than a millimeter thick, otherwise the surrounding components may be contaminated.
-
Place the graphics card on the prepared cooler. Fasten the card as shown with the 4 M2x5 screws with M2 washers. Hand-tighten the screws crosswise, one turn at a time.
-
Remove the protective foils from the thermal pads and place the pads on the PCB as shown.
-
Put the backplate on and screw it together with the 8 M2x11 screws as shown.
Alphacool International GmbH
Marienberger Str. 1
D-38122 Braunschweig
Support: +49 (0) 531 28874 – 0
Fax: +49 (0) 531 28874 – 22
E-Mail: info@alphacool.com
General Managers: Andreas Rudnicki, Nathanael Draht, Fabian Noelte
WEEE-Reg.-Nr.: DE 544444
Trade Register: Amtsgericht Braunschweig HRB 202390
VAT.ID.Nr.: DE27058421
Tax number: 13/207/02047
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>