luminii Plexineon Recessed Dynamic Color Suspension Mount Instruction Manual
- June 3, 2024
- luminii
Table of Contents
luminii Plexineon Recessed Dynamic Color Suspension Mount
Installation Instructions – Plexineon Recessed Dynamic Color
Please read all instructions prior to installation and keep for future reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
- USE ONLY WITH CLASS 2 POWER UNIT
- 24 VOLTS DC
- SUITABLE FOR WET LOCATIONS
- RECESSED MOUNT ONLY
NOTE : Prior to installation all 24VDC wires must be present within 72”
of the installation. Refer to the power supply installation instruction for
additional information.
NOTE : More than one person is recommended for this installation.
Screw end plate onto extrusion housing.
If more than one extrusion housing, use two alignment pins to connect both
side of the extrusion housing.
INSTALLATION OPTIONS
NOTE : Use paint mask to protect extrusion housing when doing a surface/
wall finishing. Install plexineon fixtures after removing paint mask
NOTE : Use plaster plate when doing a mud-in installation. Use paint mask
to protect extrusion housing during surface/wall finishing.
Wood Blocking Installation
NOTE : Blocks are provided by others.
Mud-in Installation
- Drill or punch Ø 5/8” hole into extrusion housing.
- Clamp power feed strain relief to wire.
- Snap power feed strain relief into hole.
NOTE : Drill hole on extrusion housing before install into wall/surface.
-
nstall recessed mounting clips to fixture. Make sure they are approximately 30” apart.
-
Use gule to fill in all gaps between recessed mounting clips and plexineon fixture.
-
Peel back power cord to expose wires. Connect power supply wires to fixture wires. Waterproof wire nuts recommended in this step.
-
Snap plexineon fixture with glued mounting clips into extrusion housing.
RGB &RGBW WIRING DIAGRAM
WIRING DIAGRAM
NOTE : Please make sure that power is turned off before wiring. Also,
ensure that the correct power supply (voltage and wattage) is used to power
the LED strips connected to the decoder. Follow illustrated wiring diagram.
Use screwdriver to open and close connection slots.
NOTE : When connecting two or more LED strip lights or light fixtures,
always make sure the signal direction arrows are pointing to same direction
The signal direction arrow should appear on label of each section of LED
fixture.
OPERATING GUIDE
SR-DMX-SPI
Smart Pixel LineLED Decoder
There are three buttons on the decoder.
-
Parameter Setting
-
Increase Value
-
Decrease Value
After operation, if no action was taken within 30s, the button lock, and backlight of the screen will turn off.
- Long press M button for 5s to unlock the buttons, and the backlight will turn on.
- Long press M button for 5s to switch between test mode and decode mode after unlocked.
During test mode, the first line of LCD will show: TEST MODE. Use test mode to verify RGBW Pixel functionality.
During decoder mode, the first line of LCD shows: DECODER MODE. Use decoder mode when connecting to a Controller and for final installation and customization.
| SETTING | LCD DISPLAY | VALUE RANGE | DESCRIPTION |
|---|---|---|---|
| Built-in Programs | TEST MODE MODE NO.: | 1-26 | See Program Table below |
| Program Speed | TEST MODE RUN SPEED: | 0-7 | 0: fast, |
7: slow
DMX Address| DECODER MODE DMX ADDRESS:| 1-512| Address of the starting
point/Pixel of a program
DMX Signal RGB| DECODER MODE DMX RGB SEQ:| RGB, BGR, etc.| N/A
Pixel Quantity| DECODER MODE PIXEL QTY:| 1-170(RGB),
1 128(RGBW)| Number of Pixels to follow a program
IC TYPE| DECODER MODE IC TYPE| 2903, 8903,
2904, 8904| 2903: N/A,
2904: for RGBW,
8903: N/A,
8904: N/A
Color| DECODER MODE COLOR:| MONO, DUAL, RGB, RGBW| MONO: N/A, DUAL: N/A, RGB:
N/A,
RGBW: for RGBW
Pixel Merging / Pixel Size| DECODER MODE PIXEL MERGE:| 1-100| Number of Pixels
to merge together
RGB Sequence| DECODER MODE LED RGB SEQ:| RGBW,
BGRW, etc.| Sequence of RGBW, 24 possible combinations
Integral Control| DECODER MODE ALL CONTROL:| YES, NO| Yes: Merge all Pixels
No: Maintain individual Pixels or Merged Pixels
Reverse Control| DECODER MODE REV-CONTROL:| YES, NO| Reverse program order
Overall Brightness| DECODER MODE BRIGHTNESS:| 1-100| 1: dimmest setting
100: brightest setting
NOTE :
When connected to a controller, DMX512 Signal Decoder will stay in “Decoder
Mode”.
NOTE :
The actual maximum control pixels of the controller are 1360 (2903) ,1024
(2904). Please set the pixel and pixel combination value according to the
actual situation, and DO NOT exceed the maximum.
NOTE : For Program Table Change: no fading/dimming between color changes Fade: fade/dim between color changes Chase: change pixel by pixel Chase with Trail: change pixel by pixel with fading between
PROGRAM TABLE
| PROGRAM NO. | PROGRAM DESCRIPTION |
|---|---|
| 1 | Solid color: Red |
| 2 | Solid color: Green |
| 3 | Solid color: Blue |
| 4 | Solid color: Yellow |
| 5 | Solid color: Purple |
| 6 | Solid color: Cyan |
| 7 | Solid color: White |
| 8 | RGB change |
| 9 | Full color change |
| 10 | RGB fading |
| 11 | Full color fading |
| 12 | Red chase with trail |
| 13 | Green chase with trail |
| 14 | Blue chase with trail |
| 15 | White chase with trail |
| 16 | RGB chase with trail |
| 17 | Rainbow chase with trail |
| 18 | RGB chasing and fading |
| 19 | Red chasing green, chasing blue |
| 20 | Orange chasing purple, chasing cyan |
| 21 | Rainbow chase (7 colors) |
| 22 | Random twinkle: white over red |
| 23 | Random twinkle: white over green |
| 24 | Random twinkle: white over blue |
| 25 | White fading |
| 26 | Off |
Customer Support
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
info@luminii.com
www.luminii.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>