Luminii KLBC Kendo L Bendable Instruction Manual
- May 15, 2024
- luminii
Table of Contents
Luminii KLBC Kendo L Bendable
Specifications:
- Model: Kendo L Bendable – KLBC-XX
- Power Unit: Class 2
- Operating Voltage: 24 Volts DC
- Installation: Surface Mount Only
- Location Suitability: Suitable for Damp Locations
Product Usage Instructions
Lens Extrusion Installation:
Measure and mark reference points on the surface where the extrusion will be installed. Snap the lens into the extrusion and align it to the marked location. Ensure 24VDC power is present before installation.
Cutting Extrusion and Lens:
If necessary, the extrusion and lens can be cut in the field using a proper blade for aluminum. Snap all parts together before cutting to the desired length.
LineLED Installation:
Clean the extrusion from any debris before pushing the LineLED onto it. Remove the protective film from the diffuser lens and snap it into the extrusion.
Endcap Installation:
Install endcaps at each end of the extrusion by aligning the grooves and sliding them into position.
Fixed Clip Mounting Installation:
Screw mounting brackets into the marked locations, then clip the extrusion onto the brackets.
FAQ
Q: Can the extrusion be removed from the mounting brackets?
A: Yes, to remove the extrusion, carefully insert a flat screwdriver at the bottom edge and pull up until it pops out.
Q: What safety precautions should be taken during installation?
A: Safety equipment is recommended when making modifications to the extrusion and lens.
Please read all instructions prior to installation and keep for future reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.5. SURFACE MOUNT ONLY
- USE ONLY WITH CLASS 2 POWER UNIT.
- 24 VOLTS DC.
- SUITABLE FOR DAMP LOCATIONS.
INSTALLATION
Note: Complete fixture must be built prior to installing. To make all necessary reference marks & to also ensure all parts are included. Then it can be taken apart for installation.
-
Snap lens into the extrusion, then align & center the extrusion to the determined location. Make all necessary markings to install to the surface. Prior to installation of extrusion, 24VDC power must be present.
Caution: Safety equipment is recommended, when modifications are being made to the extrusion & lens. -
If necessary extrusion and lens can be cut in the field. Snap all parts together then, using the proper blade for aluminum, cut to the desired length.
Note: Extrusion is not waterproof. If it is going to be installed facing up and in a wet location, drainage holes should be drilled along the inner corner of the extrusion every 12”. Drill 1/16” to 1/8” diameters holes before installing LED strip -
LineLED can be shortened by cutting along the dashed lines in between the solder pads. Make sure the cut is made on the side of the LineLED without the wire leads. LineLED cannot touch the metal endcap which will shorten the circuit.
-
Prior to installing LineLED to extrusion, clean extrusion from any debris. Gently push LineLED onto aluminum extrusion. Then remove the protective film from the diffuser lens and snap the diffuser lens into the aluminum extrusion.
- Install endcaps at each ends of the extrusion by aligning the groves of the endcap and sliding them into position
- Screw mounting brackets into previously made markings from step 1, then clip the extrusion on to the mounting brackets.
-
Snap the fixture into the installed mounting brackets.
Note: To remove the extrusion from the mounting brackets, carefully insert a flat screwdriver to the bottom edge of the extrusion then pull up until the extrusion pops up. -
Ensure the correct (wattage & voltage) power supply is used to power LineLED.
Then proceed to connect LineLED wires from extrusion to power supply. For more information please refer to power supply and LineLED wiring instructions.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
7777 Merrimac Ave Niles, IL 60714
T 224.333.6033
F 224.757.7557
info@luminii.com
www.luminii.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>