STETSOM VULCAN 2000 Digital Power Amplifier User Manual

: June 6, 2024
: STETSOM

Table of Contents

Introduction
Before installing
Input, output, and audio controls
Indicators LED
Smart protection system
Installation
Troubleshooting
Technical specifications
Warranty Term
EU Declaration of conformity (DoC)
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

2000
DIGITAL AMPLIFIER
USER MANUAL

Introduction

Thank you so much for choosing a Stetson product! The chosen amplifier has been developed with the most advanced technology for those who are looking for high-performance audio systems with one or more speakers and a “pro-car audio” system.

Before installing

Please read this manual carefully.

All product connections need to be made with the product turned OFF.
A fuse must be installed between the amplifier and the battery is required to protect against overcharging. The fuse has to be installed as close to the battery as possible. Check the proper fuse for the amplifier according to its consumption.
Use gauges recommended in this manual to avoid the overheating of the cables to obtain maximum power.
Keep the cables as short as possible to increase sound fidelity and avoid potential power losses.
Route the installation cables as far away as possible from the original vehicle wiring as it may cause interference and noise in your audio system.
Perform the installation in a firm, ventilated, and dry place.
A qualified professional must be done the Install.

If you have questions, contact the store where the purchase or installation was made. For more information please contact our Customer Service: BR +55 18 2104-9412.

Input, output, and audio controls

INPUT : Input of the signal to be amplified. Connect to the radio/player through high-quality shielded RCA cables to prevent unwanted noise.
LEVEL : Signal level control in the amplifier input.
CROSSOVER:
▪ HIGH PASS FILTER (H.P.F.): This variable control allows you to select the initial frequency from 10Hz to 90Hz that will be reproduced by the amplifier.
▪ LOW PASS FILTER (L.P.F.): This variable control allows you to select the final frequency from 90Hz to 22KHz that will be reproduced by the amplifier.
BASS BOOST:
▪ BASS: Variable control for bass boost from 0dB to +10dB.
▪ FREQ: Variable control for BASS boost action from 30Hz to 70Hz.
4.1 . MID BASS BOOST: Variable control from 0dB to +10dB with bass boost at 270Hz.
4.2 MID HIGH BOOST: Variable control from 0dB to +10dB with acting on boosting midrange at 2KHz frequency.
FLAT KEY: This switch allows you to turn the FLAT mode on or off. Settings made on the CROSSOVER and BOOST controls will be turned off when using this model.
OUTPUT CONNECTOR (SPEAKERS): MONO output of amplified signal for peakers connection. Check the minimum impedance and polarities before performing the installation.
Power input
COOLER: It provides cooling of the amplifier. Install in a cool place without the obstruction of air inlets and outlets.
POSITIVE POWER SUPPLY CONNECTOR: Connect to the positive battery terminal through a minimum 4 AWG cable with a fuse/circuit breaker (120A) as close to the battery as possible.
REMOTE CONNECTOR (REM): Allows automatic activation of the amplifier when turning on the radio/player. Connect to the remote output of the radio/player minimum of 20 AWG.
NEGATIVE POWER SUPPLY CONNECTOR: Connect to the negative terminal of the battery using a cable minimum of 4 AWG.

Indicators LED

POWER (blue LED): Indicates amplifier operation when it’s on.
PROT (top red LED): Indicates that the amplifier encountered malfunctions and entered protection
mode, forcing it to shut down. Verify-in the protection table below the possible problem and turn on the amplifier again.
CLIP (lower red LED): Indicates signal distortion at the amplifier output.

Smart protection system

When the protection system detects a failure, the amplifier will turn off and the PROT LED will blink. For each type of failure, the LED will flash a certain number of times indicating the cause, as shown in the table below:

Diagnostic : Short circuit or output overload.
Solution: Check that the speaker cables are well insulated and that the output impedance does not exceed that supported by the amplifier.
Diagnostic: Excessive temperature. When the amplifier reaches approximately 32°F, audio is stopped and the coolers run at maximum speed to speed up the cooling process of the internal components.
Solution: Check if the amplifier is in a ventilated place or if the coolers are not obstructed. Keep the amplifier turned on for a few minutes for the coolers to assist in the cooling process.
Diagnostic : Supply voltage less than 9V.
Solution: Check the voltage of the battery or power supply.
Diagnostic: Supply voltage greater than 16V.
Solution: Check the voltage of the battery or power supply.

Installation

Specification of the cables for proper installation:

Power connectors (positive/negative) ………………………………….4 AWG
Remote connector …………………………………………………………….18 AWG
Output signal connectors (speakers) ……………………………………9 AWG
Fuses or circuit breakers ……………………………………………………..120A

The use of a fuse or circuit breaker is mandatory to protect the system from short circuits and overload. Install them as close to the battery as possible.
Installation should only be done by qualified professionals with the product turned OFF.

Troubleshooting

AMPLIFIER DOES NOT TURN ON:

Verify that the cables are connected correctly. Make sure all connections have electrical and mechanical contact.
Fuses or circuit breakers may be defective or blown. Check the condition of the circuit breakers and if it’s compatible with the equipment consumption.
Verify that the battery charge is sufficient for the operation of the product.

NO SOUND:

The cables of the speakers or RCA plugs may not be connected correctly or are defective.
Verify that the LEVEL control isn’t at a minimum.

PROT LED FLASHING:

Verify that the product vents aren’t blocked or the product is overheated.
Speakers or cables shorted, check speakers, cables, and connections.

SOUND DISTORTIONS:

The speakers may be overloaded or defective, lower the level and remake the level adjustment. This setting can be adjusted as follows:
a) On the radio/player, place any musical signal and set the volume to 80% of the maximum (if the maximum volume of the radio /player is 45 (100%), set to 36 (80%).
b) On the amplifier, with LEVEL control at minimum, increase gradually until the LED CLIP starts to flash. Slowly return the LEVEL until the led goes out completely.

LACK OF BASS:

Cables of the speakers may be reversed and (out-of-phase speakers).

NOISE AND FAILURE IN SOUND:

Verify that the installation isn’t close to the original vehicle wiring as they may cause interference and noise in the audio signal.
Make a separate power connection to the sound system. Use a fuse/ a circuit breaker as close to the battery as possible for protection.
Make a good grounding of the amplifier. To do this, remove the paint from the vehicle chassis at the desired point. Screw the wire using a ground terminal. To protect from oxidation, isolate with paint.
Don’t loop the ground. Avoid using multiple grounds. If possible, use a star connection, in which all the grounds run from a single point.

**** Any updates made in this manual will be available for customers to consult without any charge on the brand’s site.
It is recommended that the updated manual be consulted whenever needed.
Images contained in this manual are merely illustrative and may differ from the actual product.

Technical specifications

Minimum Output Impedance:	1 OHM	2 OHMs	4 OHMs
Number of Channels	1
Power Ouput @ 14.4V:	2600W RMS@ 1 Ohms
1720W RMS@ 2 Ohms	2750W RMS @ 2 Ohms
1600W RMS @ 4 Ohms	2830W RMS @ 4 Ohms

1600W RMS @ 8 Ohms
Power Ouput @ 12.6V:| 2015W RMS @ 1 Ohm
1330W RMS @ 2 Ohms| 2115W RMS @ 2 Ohm
1140W RMS @ 4 Ohms| 2050W RMS @ 4 Ohms
1200W RMS @ 8 Ohms

Minimum Input Sensitivity:	200mV
Signal to Noise Ratio:	>90dB
Frequency Response (-3dB):	10Hz ~ 22KHz
Crossover Low Pass:	90Hz ~ 22KHz
Crossover High Pass:	10Hz ~ 90Hz
Bass Boost:	Freq: 30Hz ~ 70 Hz

The data measured are based on STETSOM laboratory equipment. Test reference in frequency from 60hz to 1Khz with THD + N at ≤1% in impedances as indicated in each measurement. The electronic components and the manufacturing process may present manufacturing variations, thus leading to a variation in the measurements made.

Warranty Term

STETSOM, through its network of Authorized Technical Assistance Providers, guarantees technical assistance to the purchaser of their products. The repairs of any defects duly established as being of the manufacturer will be done without cost for replacement components or parts and repair labor. The repairs will be done by the Authorized Technical Assistance Provider specially designated by STETSOM.
CONSULT THE LIST OF AUTHORIZED TECHNICAL ASSISTANCE PROVIDERS ON OUR WEBSITE: www.stetsom.com.br/en/assistencias-tecnica
If you do not locate technical assistance in your city, please contact us at: BR +55 18 2104-9412

WARRANTY CONDITIONS:
Our warranty is 1 (one) year against manufacturing defects. Its validity starts on the date of the Sale to the FINAL Consumer.
To make use of the benefits of this warranty, you must present one of the following documents: the Final Consumer’s SALE NOTE or this completed CERTIFICATE.
CASES THAT VOID THE WARRANTY:

1 year after the issuance of the invoice of sale to the consumer or 1 year of completing a certificate of warranty (dated and stamped by the retailer or installer) or 1 year from date of manufacture.
Violation of seals, alteration or removal of the product’s serial or lot number.
If the product suffers misuse, careless accidents involving: Water, Fire or Fall, or is installed in conditions contrary to the guidelines contained in the installation manual that accompanies the product.
Damages and changes in the circuit or adaptation of non-original parts.
If you use installation techniques contrary to those given in the manual.

QUESTIONS AND ADVICE:
STETSOM offers Customer Services to answer questions and give advice about their products and services. Please contact us through the channels:
Phone: BR +55 18 2104-9412
E-mail: suporte@stetsom.com.br — Site: www.stetsom.com

EU Declaration of conformity (DoC)

1 OHM

MODEL: VULCAN 2000 (1Ω)
Voltage Supply: 9V – 16V DC
Current Range: 1.5A – 217A DC
MADE IN BRAZIL
www.stetsom.com.br/certifications/vulcan2000_1ohm_eu- doc.pdf

2 OHMS
MODEL: VULCAN 2000 (2Ω)
Voltage Supply: 9V – 16V DC
Current Range: 1.4A – 217A DC
MADE IN BRAZIL

www.stetsom.com.br/certifications/vulcan2000_2ohms_eu- doc.pdf
4 OHMS
MODEL: VULCAN 2000 (4Ω)
Voltage Supply: 9V – 16V DC
Current Range: 1.40A – 198A DC
MADE IN BRAZIL
www.stetsom.com.br/certifications/vulcan2000_4ohms_eu- doc.pdf

Do not use normal trash for this product in case of damage or end of life.

Guarantee certificate
Serial
Date of purchase:
Year of manufacture:
Stamp:

www.STETSOM.com.br