Luminii MK45 Static White Surface Mount Linear 24V System Instructions

May 15, 2024
luminii

Luminii - logo

Myka – Installation Instructions
Models MK-XX

Luminii MK45 Static White Surface Mount Linear 24V System
-

MK45 Static White Surface Mount Linear 24V System

Please read all instructions prior to installation and keep for future reference!

  1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
  2. USE ONLY WITH CLASS 2 POWER UNIT.
  3. 24 VOLTS DC.
  4. SUITABLE FOR DAMP LOCATIONS.
  5. SURFACE MOUNT ONLY
  6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE WHEN USED WITH TAPE OUTPUTS 5.7W/FT OR LESS
  7. INHERENTLY PROTECTED

Magnetic Installation

Luminii MK45 Static White Surface Mount Linear 24V System - Magnetic
Installation

Note: : Prior to installation all 24VDC wires must be present near fixture. Refer to the power supply installation instruction for additional information.
Note: More than one person is recommended for this installation.
1.1 Determine the location of the fixture. Must be made of steel or a ferrous metal. Clean the surface area thoroughly from any debris. Snap the fixture onto the metal surface. If necessary fixture can easily be removed by rotating off the surface and repositioning correctly.

Follow one of the two options to connect the fixture to the power supply.
Option 1- Secure female quick connect to male quick connect. Feed male quick connect wire through conduit to power supply.

Luminii MK45 Static White Surface Mount Linear 24V System - Magnetic
Installation2

Connect +24 VDC red wire from the fixture to the power supply +24 VDC red wire with a wire nut. Connect -24VDC black wire from the fixture to power supply -24VDC black wire with a wire nut.

Concealed Bracket Installation

Luminii MK45 Static White Surface Mount Linear 24V System - Magnetic
Installation3

1.1 Determine the location of where the fixture(s) will be installed. Lay the fixture(s) on the surface, and make any necessary reference marks for the concealed mounting brackets. Make marks 4” from each end of the fixture(s) and also every 23” in between.

Luminii MK45 Static White Surface Mount Linear 24V System - Magnetic
Installation4

1.2 Lay the concealed bracket onto the reference mark points and secure using the provided hardware.

Luminii MK45 Static White Surface Mount Linear 24V System - Magnetic
Installation5

2.1 If necessary make any pass through holes for wire lead/connector to the surface, depending on the power feed option. Then snap the fixture into the concealed bracket to secure in place.

3.1 Follow one of the two options to connect the fixture to the power supply.
Option 1- Secure female quick connect to male quick connect. Feed male quick connect wire through conduit to power supply.

Luminii MK45 Static White Surface Mount Linear 24V System - Magnetic
Installation7

Connect +24 VDC red wire from the fixture to the power supply +24 VDC red wire with a wire nut. Connect -24VDC black wire from the fixture to power supply -24VDC black wire with a wire nut.

Adjustable Hinge Installation

Luminii MK45 Static White Surface Mount Linear 24V System - Adjustable Hinge
Installation

1.1 Slightly loosen both screws on the sides of the hinge bracket. Rotate the fixture to expose mounting hole.

Luminii MK45 Static White Surface Mount Linear 24V System - Adjustable Hinge
Installation1

Note: : Prior to installation all 24VDC wires must be  present near fixture. Refer to the power supplyinstallation instruction for additional information.
Note: More than one person is recommended for this installation.
2.1 Determine the location of the fixture. Then secure the fixture to the surface using the provided mounting screws.
2.2 Rotate the fixture to the desired angle then tighten the side screws to secure.

Follow one of the two options to connect the fixture to the power supply.
Option 1 – Secure female quick connect to male quick connect. Feed male quick connect wire through conduit to power supply.
Luminii MK45 Static White Surface Mount Linear 24V System - Adjustable Hinge
Installation3 Connect +24 VDC red wire from the fixture to the power supply +24 VDC red wire with a wire nut.
Connect -24VDC black wire from the fixture to power supply -24VDC black wire with a wire nut.
power supplies at the end of the run

Luminii MK45 Static White Surface Mount Linear 24V System - power
supplies

power supplies in the middle of the run

Luminii MK45 Static White Surface Mount Linear 24V System - power
supplies1

consecutive layout, NOT RECOMMENDED

Luminii MK45 Static White Surface Mount Linear 24V System - power
supplies2

*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE

Luminii - logo7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
info@luminii.com
www.luminii.com REV0.3
02022024

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals