NORDIC HPW-L0418 18V Cordless Pressure Washer User Manual

NORDIC HPW-L0418 18V Cordless Pressure Washer User Manual

PRODUCT SPECIFICATION

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions. Failure to heed warnings and follow instructions may result in electric shock, fire and/or serious injury.

Keep safety warnings and instructions for future reference.

The term “power tool” in the safety warnings refers to your mains operated (corded) power tool or batteryoperated (cordless) power tool.

WORKING AREA

• Keep working area clean and well lit. Untidy and dark areas can lead to accidents.
• Do not operate power tools in potentially explosive surroundings, for example, in the presence of inflammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders at a distance when operating a power tool. Distractions can cause you to lose control of it.

ELECTRICAL SAFETY

• Always check that the power supply corresponds to the voltage on the rating plate.
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce the risk of an electric shock.
• Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and refrigerators. There is an increased risk of an electric shock if your body is earthed.
• Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will increase the risk of an electric shock.
• Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of an electric shock.
• When operating a power tool outdoors, use an extension cable suitable for outdoor use. Using a cord suitable for outdoor use reduces the risk of an electric shock.
• If operating a power tool in a damp location is unavoidable, use a power supply protected by a residual current device (RCD). Using an RCD reduces the risk of an electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when operating a power tool may result in serious personal injury.
• Use safety equipment. Always wear eye protection. Using safety equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed will reduce the risk of personal injury.
• Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more likely.
• Remove any adjusting keys or spanners before turning on the power tool. A spanner or key left attached to a rotating part of the power tool may result in personal injury.
• Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable you retain control over the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from the power tool. Loose clothes, jewellery or long hair can become entangled in the moving parts..
• If there are devices for connecting dust extraction and collection facilities, please ensure that they are attached and used correctly. Using such devices can reduce dust-related hazards.

POWER TOOL USE AND CARE

• Do not expect the power tool to do more than it can. Use the correct power tool for what you want to do. A power tool will achieve better results and be safer if used in the context for which it was designed.
• Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store power tools, when not in use, out of the reach of children and do not allow people who are not familiar with the power tool or these instructions to operate it. Power tools are potentially dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or jammed moving parts, breakages or any other feature that might affect the operation of the power tool. If it is damaged, the power tool must be repaired. Many accidents are caused by using poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.
• Use the power tool, accessories and cutting tools, etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work which needs to be done. Using a power tool in ways for which it was not intended can lead to potentially hazardous situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

SERVICE

Your power tool should be serviced by a qualified specialist using only standard spare parts. This will ensure that it meets the required safety standards.

Special safety instructions for Presure Washer

• Do not shoot water at the equipment containing electrical components
• Do not let children use this product
• Please discontinue use when the product accidentally falls to the ground, showing visible damage or failure.
• Please use dry cloth to wipe products for cleaning. Do not use water, gasoline, alcohol and other chemical solvents.
• Please clean the water inlet filter and wipe water pipe filter regularly.
• Waste batteries should be classified for recycling
• This product shall operate by connecting water through inlet pipe. Do not make it operate long time without water connection.

ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS

Use only batteries and chargers applicable for this machine.

BATTERIES

• Never attempt to open for any reason.
• Do not store in locations where the temperature may exceed 40 °C.
• Charge only at ambient temperatures between 4 °C and 40 °C.
• When disposing of batteries, follow the instructions given in the section “Protecting the environment”.
• Do not cause short circuits. If connection is made between the positive (+) and negative (-) terminal directly or via accidental contact with metallic objects, the battery is short circuited and an intense current will flow causing heat generation which may lead to casing rupture or fire.
• Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators and other polymer components may be damaged resulting in electrolyte leakage and/or internal short circuiting leading to heat generation causing rupture or file. Moreover do not dispose of the batteries in fire, explosion and/or intense burning may result.
• Under extreme conditions, battery leakage may occur. When you notice liquid on the battery, proceed as follows:
• Carefully wipe the liquid off using a cloth. Avoid skin contact.
• In case of skin or eye contact, follow the instructions below:

1. Immediately rinse with water. Neutralize with a mild acid such as lemon juice or vinegar.
2. In case of eye contact, rinse abundantly with clean water for at least 10 minutes.
3. Consult a physician.

Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do not incinerate the battery.

CHARGERS

• Never attempt to charge non-rechargeable batteries.
• Have defective cords replaced immediately.
• Do not expose to water.
• Do not open the charger.
• Do not probe the charger.
• The charger is intended for indoor use only.

SYMBOLS

In this manual and/or on the machine the following symbols are used:

Denotes risk of personal injury or damage to the tool.
Read manual before use
Wear eye protection
Wear ear protection
Wear safety gloves
Wear respiratory protection
In accordance with essential requirements of the European directive(s)
Class II – The machine is double insulated; Earthing wire is therefore not necessary (only forcharger)
Ambient temperature 40°C max. (only for battery)
Do not expose charger and battery pack to water
Use battery and charger only in closed rooms
Do not incinerate battery pack or charger

CLEANING AND MAINTENANCE

CLEANING

• Keep the ventilation slots of the machine clean to prevent overheating of the engine.
• Regularly clean the machine housing with a soft cloth, preferably after each use.
• Keep the ventilation slots free from dust and dirt.
• If the dirt does not come off use a soft cloth moistened with soapy water.
• Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.

MAINTENANCE

Our machines have been designed to operate over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper machine care and regular cleaning.

REPAIR

This product does not contain any parts that can be repaired by the consumer. Contact a qualified specialist to have it checked and repaired.

ENVIRONMENT

Should your appliance need replacement after extended use, do not dispose of it with the household refuse, but in an environmentally safe way.
Waste produced by electrical machine items should not be handled like normal household rubbish. Please recycle where recycle facilities exist. Check you’re your Local Authority or retailer for recycling advice.

Name of all parts

All accessories are subject to the real objects. The following pictures and text are only used for installation instructions.

1. High/Low pressure button
2. Soap lye pot
3. Multi-water gun
4. Multi-function jet pipe
5. Inlet pipe
6. Pipe connector
7. Extension pipe
8. Water pipe filter
9. Battery charger
10. Lithium battery pack
11. Battery lock
12. Water inlet
13. Trigger lock
14. Trigger

Use scenarios
The lithium battery high pressure cleaner is suitable for multi-scene and multi-object cleaning, such as car, bicycle, road, glass, barbecue oven, flowers watering etc.

Installation and use

Installation of the lithium battery pack and host

1. Follow the arrow direction shown and aim the guide rail of the lithium battery pack under the handle of the host until the battery is locked.
2. Please press the buttons on both sides of the lithium battery pack and pull it out backward at the same time when the pack is removed.
   Note: Avoid battery getting any water during installation.

Installation and use of the extension pipe, jet pipe and soap lye pot

Note: This cleaning machine can be equipped with extension pipe and a variety of jet pipes, such as multi-function jet pipe, rotatable jet pip. Also with a soap lye pot. Users can choose the appropriate accessories according to the washing object. Do not point the jet pipe towards other people or yourself during your use.

Installation of extension pipe

1. Insert the extension pipe into the bottom of the host interface, then rotate the extension pipe clockwise, the installation is finished successfully.
2. Press the extension pipe toward the direction of the host interface, rotate the extension pipe anticlockwise, then the extension pipe will be unplugged.

Installation and use of the foam lye pot

1. put the foam lye pot upward into joint of the multi-function jet pipe, then rotate the foam lye pot clockwise to lock. Then the foam lye pot will be installed successfully.
2. Press the foam lye pot upward to the multi-function jet pipe, then rotate the foam lye pot anticlockwise to unlock. Then the foam lye pot can be unplugged successfully.

Installation and use of the rotatable jet pipe

1. Insert the rotatable jet pipe into the joint of the extension pipe. Then rotate clockwise, the installation will be finished successfully.
2. Rotate according to the picture , then the direction of outlet water can be adjusted.
3. Press the rotatable jet pipe and rotate anticlockwise. The extension jet pipe will be unplugged.

Installation and use of the multi-function jet pipe

1. Insert the multi-function jet pipe into the joint of the extension pipe, rotate the multi-function jet pipe clockwise to lock
2. Press the multi-function jet pipe then rotate the multi-function jet pipe anticlockwise to unlock, then the multi-function jet pipe will be unplugged.
3. Mode selection of water jetting There are six effects of water jetting which are 0°, 20°, 20° slant direction, 40°, foam jetting, and shower mode or 0° heavy flow. Please choose the appropriate water jetting mode according to the washing condition. Multi-function jet pipe of the flower jetting is for irrigation etc use. Rotate the outer ring of the jet pipe to select the intended water jetting pattern.

Installation and use of the water inlet pipe

1. Hold the pipe connector as shown in the picture and insert it into the water inlet of the pressure cleaner host.
2. Hold the connector and pull it down to remove the water inlet pipe.

The charging of lithium battery pack

Before use, press the indicating button of battery on the ithium battery pack to check the battery power state.

When the battery indicator is not all lighted which indicates the low power, please use the charger coming with the high pressure cleaner to charge first

As shown in the picture below, please point the charging plug of the charger at the charging interface of the lithium battery pack to start charging.
Note: Please observe the charger indicator to confirm the charging state: The indicator is red to indicate that it is charging. The indicator turns green is to indicate it is fully charged.

The selection of working mode

1. There are Auto (automatic) and Eco (economical) modes which can be switched by pressing the mode button.
2. To get fast water jetting, it is suggested to choose the Auto mode when the high pressure cleaner starts. The working mode can be switched after the normal water jetting.
3. To get fast water jetting, there is no need to connect the jet pipe first. Press and hold the trigger until the cleaner jets water normally and then connect the jet pipe to work correctly.

Clean and Maintenance

Tip: Please remove the battery from the cleaner machine before cleaning.

1. Water inlet filter. Clean the fitter regularly to prevent blocking of the water inlet which will result in no or decrease of water jetting. Clean method: Remove the filter and clean it as shown in the picture below.

2. Water pipe filter. Clean the filter regularly to prevent blocking of the water pipe inlet which will result in the water inlet not smoothly.
   Clean method: Unscrew the outer cover of the water pipe filter and draw out the filter for cleaning.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>