PARKSIDE PDS 30 A1 Extendable Ceiling Support Rod Instruction Manual

: June 3, 2024
: PARKSIDE

Table of Contents

PDS 30 A1 Extendable Ceiling Support Rod
Information on these operating instructions
Intended use
Technical details
Safety instructions
Parts and operating components
Usage
**Disposal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EXTENDABLE CEILING SUPPORT ROD
Operating instructions PARKSIDE PDS 30 A1 Extendable Ceiling Support
Rod

PDS 30 A1 Extendable Ceiling Support Rod

PARKSIDE PDS 30 A1 Extendable Ceiling Support Rod - qr
code PDF ONLINE
www.lidl-service.com

IAN 380865_2110
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device. PARKSIDE PDS 30 A1 Extendable
Ceiling Support Rod - Figure 1

Information on these operating instructions

Congratulations!
You have purchased a high-quality product. Familiarise yourself with the product before using it for the ﬁrst time. To do this, read the following operating instructions and the safety instructions thoroughly. Use the product only as described and for the range of applications speciﬁed. Keep these operating instructions in a safe place. Please pass this manual on to any future owner.

Intended use

The ceiling prop is intended exclusively for private use as a support during overhead work in dry and interior construction. The prop is not designed for use on stairways or sloping ground. Commercial or industrial use is not permitted. No liability will be assumed in cases of improper use.
No liability will be assumed for damage caused by misuse or improper handling, the use of force or unauthorised modiﬁcation. The risk is borne solely by the user.

Technical details

Dimensions

Safety instructions

CAUTION! RISK OF INJURY!

Check the prop before every use to make sure it is in perfect condition. If you notice any damage you may no longer use the prop.
Ensure that the prop locking screw is always tightly fastened when under load and that both locking bolts are completely engaged.
Only use the prop on clean, non-slip and level ground and in a stable position.
Check the prop before every use to make sure it is in perfect technical condition.
Never remain under supported loads.

CAUTION! PROPERTY DAMAGE!

Only use the prop for short-term erection and not for permanent propping of ceilings, beams etc.
Please note that the prop or the supporting material can be damaged by high pressure.
Never place more than 30 kg payload on the prop at an inclination of 90°. At a lower inclination, the max. load of the prop is lowered signiﬁcantly.
Use the prop only at an inclination between 65° and 90°.
Never use the prop for purposes other than those described in these instructions.

Parts and operating components

(See fold-out page for illustrations)
The ceiling prop PDS 30 A1 consists of the following parts:

Rubber pad 1
Upper bar 2
Pump lever 3
Lower bar 4
Locking screw 5
Tube 6
Locking bolt 7
Locking lever 8

Usage

Loosen the locking screw 5 (Fig. A).
If necessary, press the two locking bolts 7 out of their detent (Fig. B) and pull the lower bar 4 out up to the required height until the rubber pad 1 is located under the load to be supported (Fig. C).
Allow the two locking bolts 7 to engage completely in the tube 6 detent. Use the red line which marks the position of the locking bolts 7 (Fig. D) on the lower bar 4 as an orientation aid.
If the length of the lower bar 4 is insuﬃcient, push the locking lever 8 upwards (Fig. E) and pull the upper bar 2 out to the required height.
Re-tighten the locking screw 5 (Fig. F).
To make ﬁne adjustments to the height, press the pump lever 3 several times until the rubber pad 1 is located ﬁrmly under the load to be supported (Fig. G).
To loosen and remove the prop, press the locking lever 8 upwards until the upper bar 2 has been completely retracted (Fig. H).
Loosen the locking screw 5 (Fig. A).
Hold the tube 6 ﬁrmly with one hand and press the engaged locking bolts 7 out of their detent (Fig. B).
Push the lower bar 4 back inside completely.

PARKSIDE PDS 30 A1 Extendable Ceiling Support Rod - Figure
2 Storage
♦ Store the prop in a dry location and in a lying position so that it cannot fall over.
Maintenance
♦ The prop is maintenance free.
Cleaning
♦ Clean the prop using a brush or a slightly damp cloth.

**Disposal

**

Disposal of the appliance
Dispose of the product via an approved waste disposal company or your municipal waste disposal facility. Please comply with all applicable regulations.
Please contact your waste disposal facility if you are in any doubt.
Your local community or municipal authorities can provide information on how to dispose of the worn-out product.
The product is recyclable, subject to extended producer responsibility and is collected separately.
Disposal of the packaging
The packaging materials have been selected for their environmental friendliness and ease of disposal, and are therefore recyclable.
Dispose of packaging materials that are no longer needed in accordance with applicable local regulations.
Dispose of the packaging in an environmentally friendly manner.
Note the labelling on the packaging and separate the packaging material components for disposal if necessary. The packaging material is labelled with abbreviations (a) and numbers (b) with the following meanings:
1–7: plastics
20–22: paper and cardboard,
80–98: composites.
Service
Service Great Britain
Tel.: 0800 404 7657
E-Mail: kompernass@lidl.co.uk
Importer
Please note that the following address is not the service address.
Please use the service address provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com