ButtKicker BK-LINK2 Wireless Package Owner’s Manual
- June 6, 2024
- ButtKicker
Table of Contents
- IMPORTANT SAFETY INSTRUCTIONS
- **Usage Guidelines
- **Wireless Link2 Specifications
- Wireless Transmitter
- Wireless Transmitter Front of Unit
- Rear of Unit
- Bottom of Unit
- Wireless Receiver
- Wireless Receiver Front of Unit
- Rear of Unit
- Bottom of Unit
- Wireless Pairing
- Limited Warranty
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Wireless Link2 BK-LINK2
OWNER’S MANUAL
Serial Number:
Please record the serial number from the rear panel of your amplifier for reference.
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE OPERATING EQUIPMENT
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. ****
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not perate normally, or has been dropped.
WARNING
Do not ingest the battery, Chemical Burn Hazard (The remote control supplied
with) This product contains a coin/button cell battery. If the coin/button
cell battery is swallowed, it can cause severe internal burns in just 2 hours
and can lead to death.
Keep new and used batteries away from children. If the battery compartment
does not close securely, stop using the product and keep it away from
children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
**Usage Guidelines
**
For use with powered subwoofers and audio amplifiers.
**Wireless Link2 Specifications
**
Dimensions (Transmitter & Receiver): 3.75″ Lx 3.75″ W x 1.25″ H 9.5cm x 9.5cm x 3.175cm
Weight: | 1.1 lbs./ 0.5 kgs. |
---|---|
Frequency: | 2.4GHz ISM |
Latency: | 15mSec |
Usage: | Worldwide |
Range: | 30’ (9M) Line of Sight 7 20’ (6M) Obstructed |
DC Power Input: | OV 1 Amp |
Audio Frequency
Response Range: | 1OQHz – 2OkHz |
---|---|
Output Level: | 2 70OmVrms |
THD: | 250mvV < 0.1% |
SNR: | > 7/5dB |
Wireless Transmitter
Wireless Transmitter Front of Unit
Status LED
Displays the status of the Wireless Receiver. Please see Pairing
Instructions (Pg. 1Q) for additional information.
Blinking Blue LED: Power is ON, and the unit is attempting to pair with the
Wireless Receiver.
Solid Blue LED: Power is ON, and the unit is paired with the Wireless
Receiver.
Rear of Unit
DC Power Adapter Input
Connect the included 5V 1A DC Power Adapter.
Signal IN
RCA / phono input jack. Connect to the subwoofer (or other) output of your
audio device.
Bottom of Unit
PAIRING SWITCH
Pair Transmitter and Receiver. See instructions on page 10.
Wireless Receiver
Wireless Receiver Front of Unit
Status LED
Displays the status of the Wireless Receiver. Please see Pairing
Instructions (Pg. 10) for additional information.
Blinking Blue LED: Power is ON, and the unit is attempting to pair with the
Wireless Transmitter.
Solid Blue LED: Power is ON, and the unit is paired with the Wireless
Transmitter.
Rear of Unit
DC Power Adapter Input
Connect the included 5V 1A DC Power Adapter.
Signal OUT
RCA / phono input jack. Connect to your subwoofers’ (or power amplifiers’)
input Jack.
Bottom of Unit
PAIRING SWITCH
Pair Transmitter and Receiver. See instructions on page 10.
Wireless Pairing
Pairing Instructions
Connect the supplied DC Adapters to the Transmitter and Receiver. A Blue
LED will illuminate and blink before remaining solid.
Push the Pairing Switch located on the bottom of the Transmitter once. The
Blue LED will blink rapidly.
Push the Pairing Switch located on the bottom of the Receiver once.
The Blue LED will blink rapidly. Pairing is successful when both the
Transmitter and Receiver’s LED is illuminated and no longer blinking.
If the pairing fails repeat the above steps. If the units lose connection then
the blue LED on both the Transmitter and Receiver will begin blinking, to pair
repeat the above steps.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC warning: Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
If you have questions or need technical support, please contact The Guitammer Company, not the store where you purchased the product.
The Guitammer Company
Email us at support@guitammer.com
Visit us on the web at www.thebuttkicker. com
More Information
Visit www.thebuttkicker.com for support, FAQs,
more information and details on this, and other ButtKicker® brand products and
accessories.
Limited Warranty
Your ButtKicker BK-LINK@2 is warranted against failure for 1 YEAR unless
otherwise stated. The Guitammer Company will service and supply all parts at
no charge to the customer providing the unit is under warranty. Shipping costs
are the responsibility of the customer. THE GUITAMMER COMPANY DOES NOT PAY FOR
PARTS OR SERVICING OTHER THAN QUR OWN. A COPY OF THE ORIGINAL INVOICE IS
REQUIRED TO VERIFY YOUR WARRANTY.
The Guitammer Company assumes no responsibilities for ButtKicker® low-
frequency audio transducers or speakers damaged by this unit. This warranty
does not cover, and no liability is assumed, for damage due to: natural
disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect
use, or failure to follow instructions. This warranty is in lieu of all other
warranties, expressed or implied. No representative or person is authorized to
represent or assume for The Guitammer Company any liability in connection with
the sale of servicing of products of The Guitammer Company. THE GUITAMMER
COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. When
RETURNING merchandise to The Guitammer Company, you may call or email for a
return authorization number. Describe in writing each problem. If your unit is
out of warranty, you will be charged the current FLAT RATE for parts and labor
to bring your unit up to factory specifications.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>