Ruijie E4 Reyee Router Instruction Manual

: May 15, 2024
: RuiJie

Table of Contents

Ruijie E4 Reyee Router
Initial Configuration:

Ruijie E4 Reyee Router

Product Specifications:

1 x WAN Port
1 x 1GE LAN Port
1 x 1GE Ethernet Port (WAN/LAN)
Power Input Plug
Reset Button

Installing the Router:

Check packaging contents: Router, Power Adapter, User Manual, Warranty Card.
Connect WAN Port to ISP Modem using an Ethernet cable.
Connect Power Supply to the router.
Wait for the system status LED to turn solid on.

Initial Configuration:

Once the LED is solid, follow these steps:

Connect your PC to the SSID @Reyee-sXXXX broadcast by the router.
You will be redirected to the configuration page automatically.
If not redirected, access Web management IP address 192.168.110.1 via a browser to configure.

Managing the Router

App-based Configuration: Scan QR code to download Reyee App for managing the router.
Web-based Configuration: Connect PC to router’s SSID and access IP address 192.168.110.1 for configuration.

Through Reyee Mesh

Connect primary router to the Internet and configure it.
Place secondary router 2 meters away, power it on, and wait for LED status change.
Press Reyee Mesh button on primary router for mesh pairing.
Wait for both Reyee Mesh LEDs to turn solid on indicating successful pairing.

With Ethernet Cables

Connect primary router to the Internet and configure it.

Frequently Asked Questions (FAQs):

Q: How do I access the configuration page if it does not pop up automatically?
A: Access the Web management IP address 192.168.110.1 via a browser to perform configuration as prompted.
Q: What does a blinking orange system status LED indicate?
A: The signal strength of the mesh link is low (secondary router).

Installing a Single Router

$Ruijie-E4-Reyee-Router- $2$$

If the configuration page does not pop up, access the Web management IP address 192.168.110.1 by browser to perform configuration as prompted.

RG-E4

About the RG-E4 Router

$Ruijie-E4-Reyee-Router- $3$$

1GE LAN Port
1GE Ethernet Port (WAN/LAN)
1GE WAN Port
Power Input Plug
Reset Button
Reyee Mesh Button
$Ruijie-E4-Reyee-Router- $4$$

Reyee Mesh LED

Status	Description
Solid on	Mesh pairing succeeds.
Off	Mesh pairing is not performed.

/Mesh network is disconnected.

Blinking| Mesh pairing is in progress.

System Status LED

Status	Description
Green	Solid on

Nameplate

Nameplate The nameplate contains product name, model, power parameters, and default IP address.

Managing the Router

Method 1: App-based ConfigurationScan the QR code to download the Reyee App to manage the router. You can check the connection status and change the Wi-Fi name and password through Reyee App.
Method 2: Web-based ConfigurationConnect the PC to the SSID broadcast by the router.

Access the Web management IP address 192.168.110.1 by browser to perform configuration.

Connecting Multiple Routers Through Reyee Mesh

$Ruijie-E4-Reyee-Router- $5$$

Connect the first router to the Internet and configure it as the primary router.
For the configuration steps, see the preceding section.
Place the secondary router 2 meters (6.56 in.) away from the primary router, and power it on.
Wait for a few minutes until the system status LED on the secondary router turns from blinking green to solid red, indicating that the router completes startup.
Ensure that the secondary router is in its factory settings. If the router has been configured before, press the Reset button for 10 seconds to restore the router to factory settings before performing step 3.
Press the Reyee Mesh button on the primary router. Mesh pairing succeeds in 2 minutes.
The Reyee Mesh LEDs on both routers blinks for about 2 minutes during mesh pairing. When both LEDs stop blinking and turn solid on, mesh pairing succeeds. The Wi-Fi name and password of the secondary router are automatically synchronized with those of the primary router.
Place the secondary router where the Wi-Fi signal strength needs to be improved and then power on the router.
There is no need to configure the secondary router after power-on. After the system status LED turns solid green, you can connect to the SSID broadcast by the router for Internet access.

If the system status LED is solid orange or red, move the two routers to avoid a long distance, or too many walls or other obstacles between them.
If you have multiple routers, repeat steps 2 to 4 to connect them one by one. Up to six routers are allowed for mesh networking, including one primary router and five secondary routers.

Connecting Multiple Routers with Ethernet Cables

$Ruijie-E4-Reyee-Router- $7$$ Connect the first router to the Internet and configure it as the primary router.
Insert one end of the Ethernet cable into the WAN port (yellow) of the secondary router and connect the other end to the LAN port of the primary router. Power on the routers and wait for a few minutes until the system status LED turns solid green. Press the Reyee Mesh button on the primary router to complete wired mesh pairing. The Wi-Fi name and password of the secondary router are automatically synchronized with those of the primary router.

Ensure that the secondary router is in its factory settings. If the router has been configured before, press the Reset button for10 seconds to restore the router to factory settings before performing step 2.

Power Consumption

The router complies with the European Commission (EC) Regulation No. 1275/2008 and Regulation No. 801/2013.

Enable or disable Wi-Fi: Log in to the Web management system. Choose More > WLAN > Wi-Fi > Dual-Band Single SSID to enable or disable Wi-Fi.
Network standby power: < 8 W
Default time for power management: The product enters network standby power mode immediately after data transmission stops.
You are advised to unplug the power cord if the product is not used for a long time.
For details, log in to the product website https://www.ireyee.com/products to view the related document.

Customer service: techsupport@ireyee.com

FAQs

What can I do if I fail to log in to the Web management system (192.168.110.1) of the router?
Ensure that the PC’s NIC is set to Obtain an IP address automatically.
Make sure that the PC is connected to one of the LAN1/2/3 ports and the port status LED is on. Otherwise, replace the Ethernet cable with a new one.
Restart your browser (Google Chrome is recommended) and retry by entering 192.168.110.1 in the address bar.
Use other Web browsers.
Replace the Ethernet cable or the PC.
If the issue cannot be resolved after the preceding operations, restore the router to factory settings by pressing the Reset button for 10 seconds.
What can I do if I cannot access the Internet after configuring the router?
Check that the Ethernet cable is properly connected as instructed in the section Installing a Single Router. Make sure that the port status LED is on.
Choose Internet on the web page to check the Internet access mode.
If your ISP has provided a broadband account and password, select PPPoE and enter the account and password. If your ISP has provided IP address, subnet mask, gateway, and DNS server, select Static IP and enter the parameters.
If you still fail to access the Internet, contact your ISP for help.
What can I do if I forget the management password?
Try to log in using the Wi-Fi password. If it does not work, restore the router to factory settings.
How to restore the router to factory settings?
Use a pin to press and hold the Reset button for 10 seconds until the system status LED starts blinking, and then release the button. After the system status LED turns solid on, the router will broadcast the SSID @Reyee-sXXXX, indicating that the router is restored to factory settings successfully.