Gsou CX10 Full HD Conference Camera
- June 14, 2024
- Gsou
Table of Contents
Full HD 1080p
10X OPTICAL ZOOM
CX10 Conference Camera
User Manual
Figure of Product Interface
- Lens
- Body
- IR Receiver, power indicator
- USB IN External pickup device
- USB 2.0 interface
- RS485 IN interface
- RS232 IN interface
- DC 12V power socket
- Hole for Installing screw
- Hole for positioning
Remote Control Description
1. POWER
Pressing it, the camera goes into Standby Mode;
Pressing again, the camera goes into Power-On Mode, it will self-test again
and back to HOME position.
(Note: If the preset position 0 is set, the camera will automatically go to
the specified preset position in the power-on mode.)
2. CAMERA SELECT
Choose the camera address ready for control.
3. POSITION: Set or run presets.
4. # (Key combination use.)
**5. * (Key combination use.)
6. Focus
Auto: Enter into auto focus mode.
Manual: Enter into auto focus mode.
FOCUS+: Manually adjust the focus.
FOCUS-: Manually adjust the focus.
7. Zoom
ZOOM+: Lens near.【 ZOOM-】: Lens far.
8. SET PRESET
SET PRESET + 0-9 number key.
9. CLEAR PRESET
CLEAR PRESET + 0-9 number key.
10. PAN-TILT
(∧)Up (∨)Down (<)Left (>)Right.
HOME: Back to the horizontal and vertical center position.
11. BLC ON/OFF
Not applicable to this model.
12. MENU
Not applicable to this model.
13. Camera IR remote control address setting
【】+【＃】+【F1】: Camera address No.1
【】+【＃】+【F2】: Camera address No. 2
【】+【＃】+【F3】: Camera address No. 3
【】+【＃】+【F4】: Camera address No. 4
Key combination Functions*
【】+【#】+【#】: Clear all presets.
【】+【#】+【6】: Restore factory defaults.
【】+【#】+【7】: Image mirror.
【*】+【#】+【9】: Image flip.
After the camera is powered on, it starts to initialize. Both the horizontal
and vertical positions are turned to the middle position. The motor stops
running and the initialization is completed.
( Note: if No.0 preset position is set, the head will put it to No.0
preset position)
Packing Listing of Product
| CX10 conference camera | Installation bracket | Installation screw |
|---|---|---|
| IR Remote control | 5 meter USB line |
Product Specification
| Product Size | 155mm x 170mm x 176mm/ 1.3kg |
|---|---|
| Image Sensor | 1/2.8-inch HD CMOS Sensor |
| Effective Pixels | 2.1 Megapixel |
| Video Format | 920×1080@30fps, 1280×720@30fps |
800×600@30fps, 640×480@30fps, 320×240@30fps
Angle of View| 3x: 35.1~117.1° 10x: 7.15~67.6°
Minimum Illumination| 0.1Lux
White Balance| automatic
Focus| 3x: automatic 10x: automatic
SNR| >52dB
Interface
HD Video| USB 2.0
USB Protocol| UVC 1.1
PTZ Control| RS232 and RS485
Serial Port Data Format| Data Bits: 8/ Stop Bits: 1/ Check Bits: None Baud
Rate: 4800/9600
Power Interface| HEC 3800 Power Socket
Operating System Supported| Windows 7/ 8.1/10, Linux, Mac OS 10.10 or higher
PTZ Parameter
Pan Angle/Speed| 0~350°, 1~100°/ second
Tile Angle/Speed| -30°~90°,1-60°/ second
Preset Positions| 255(RS232/RS485), 9(Infrared Remote Control)
PTZ Protocol| VISCA,PELCO-D,PELCO-P
Power Adaptor| Input: 100-240VAC 50/60Hz/ Output: 12V DC 2A
Input voltage| 12V DC
Rated Power | 10W(Max)
Storage Temp | -10°C to +60°C
Operating Temp| 0°C to +45°C
Use Environment | Indoor
Note:
- After the code switch is changed, the camera needs to be restarted to take effect.
- Bit 8 must be the ON position to work normally.
- As long as the PTZ address matches the back-end host, the protocol will be automatically identified and supports PELCO-D, PELCO-P and VISCA protocols.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>