PARKSIDE IAN376306_2104 Temperature and Humidity Monitor User Manual

PARKSIDE IAN376306_2104 Temperature and Humidity Monitor

Product Information

• Product Name: Temperature and Humidity Monitor
• Manufacturer: Impala Services Limited
• Page Size: A5
• Model Number: IAN 376306_2104
• Dimensions: 148 mm x 148 mm

Product Usage Instructions

1. Before First Use: Read the instruction manual carefully before using the product. Make sure to follow the safety, use, and disposal instructions provided.
2. Software Installation: Follow the software installation instructions provided on page 12 of the instruction manual.
3. Operation: Follow the operation instructions provided on page 27 of the instruction manual to use the product effectively.
4. Warranty Claim Procedure: In case of any issues with the product, follow the warranty claim procedure provided on page 33 of the instruction manual.
5. Service: For any service-related queries or issues, refer to page 33 of the instruction manual.

Note: The instruction manual contains important safety information, operation instructions, and warranty details. It is recommended to read the manual carefully before using the product.

148 mm

148 mm

done by Impala Services Limited

Page size: A5

OWIM GmbH & Co. KG Stiftsbergstraße 1 74167 Neckarsulm GERMANY Model No.: HG08330 Version: 12/2021
IAN 376306_2104
00_376306_Software_UM_GB_IE_NI_MT_CY_Cover.indd 1-2

TEMPERATURE AND HUMIDITY MONITOR

TEMPERATURE AND HUMIDITY MONITOR
Operation and safety notes

IAN 376306_2104

18/01/2022 6:52:43 pm

GB/IE/NI/MT/CY Operation and safety notes
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 3

Page

3

18/01/2022 6:52:37 pm

GB/IE/NI/MT/CY 3
18/01/2022 6:52:37 pm

Warnings and symbols used
The following warnings are used in the instruction manual and on the packaging:

DANGER! This symbol in combination with the signal word “Danger” marks a high-risk hazard that if not prevented could result in death or serious injury .

NOTE: This symbol in combination with “Note” provides additional useful information .
This symbol means that the operating instructions must be observed before using the product .

WARNING! This symbol in combination with the signal word “Warning” marks a medium-risk hazard that if not prevented could result in death or serious injury .

Direct current/voltage Battery included

CAUTION! This symbol in combination with the signal word “Caution” marks a low-risk hazard that if not prevented could result in minor or moderate injury .

This mandatory sign indicates to wear suitable protective gloves! Follow the instructions of this warning to avoid hand injuries caused by objects or contact with hot or chemical materials .
Danger ­ risk of explosion!

ATTENTION! This symbol with the signal word “Attention” indicates a possible property damage .

CE mark indicates conformity with relevant EU directives applicable for this product .

Introduction
We congratulate you on the purchase of your new product . You have chosen a high quality product . The instructions for use are part of the product . They contain important information concerning safety, use and disposal .

Before using the product, please familiarise yourself with all of the safety information and instructions for use . Only use the product as described and for the specified applications . If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it .

4 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 4

18/01/2022 6:52:37 pm

Intended use

This product is suitable for measuring temperature and humidity accurately with large data storage capacity .
The measured temperature and humidity readings are saved by the product and can be analysed using software . The measurements can be started automatically or manually .
The product is only intended for use in private households, and not intended for commercial use . This product is only for indoor use .

Scope of delivery
1x Temperature and Humidity Monitor 1x Battery (CR2032) 1x Wall holder 2x Screws 2x Wall plugs 1x Instruction manual

Technical data

Battery type: Operating voltage: IP protection:

CR2032 (button cell) 3 V IP20

Range: Accuracy: Resolution:

Temperature ­30 to +70 °C ±0 .5 °C 0 .1 °C

Working temperature and humidity: ­30 to +70 °C

Storage temperature: Maximum data storage:

­50 to +70 °C 32,000 measured temperature data

Humidity 0 to 100 % RH ±2 .5 % RH 0 .1 % RH 99 .9 % non-condensable ­ 32,000 measured humidity data

Trademark notices
Windows and Windows 7 / 8 / 10 / XP are registered trademarks of Microsoft Corporation in the USA and other countries . USB® is a registered trademark of USB Implementers Forum, Inc . Intel and the Intel logo are trademarks of Intel Corporation or its subsidiaries . Any other names and products may be trademarks or registered trademarks of their respective owners .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 5

GB/IE/NI/MT/CY 5
18/01/2022 6:52:37 pm

Safety instructions

Before using the product, please familiarise yourself with all the operating and safety instructions . Please include all documentation when passing this product on to others .
m WARNING! RISK OF LOSS OF LIFE
OR ACCIDENT TO INFANTS AND CHILDREN! Never leave children unsupervised with the packaging material . The packaging material represents a danger of suffocation . Children frequently underestimate the dangers . Always keep children away from the packaging material . This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved . Children shall not play with the product . Cleaning and user maintenance shall not be made by children without supervision . Before use: Check the product for damage . If the product is damaged, do not use it . Do not expose the product to moisture . Otherwise the product could be damaged .

Unauthorized conversion and/or modification of the product is not allowed for reasons of safety . The product must not be subjected to heavy mechanical stress . Handle the product carefully and do not drop it . Knocks, blows or even a fall from a low height can damage the product . Do use the product in rooms or at unfavourable ambient conditions in which there may or could be combustible gases, vapours or dust . Avoid an operation near strong magnetic/ electromagnetic fields, transmitting aerials or HF generators, since this could affect the measurement . Do not switch on the product immediately after it has been taken from a cold into a warm environment . The condensation that forms might destroy your product . Allow the product to reach ambient temperature before switching on the product . The product must not be exposed it to extreme temperatures, direct sunlight, intense vibration or strong mechanical stress and dampness . Do not open or dismantle the housing . Do not touch or block the sensor holes [6] .

6 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 6

18/01/2022 6:52:37 pm

Safety instructions for batteries
m DANGER TO LIFE! Keep batteries out of
reach of children . If accidentally swallowed seek immediate medical attention .
DANGER OF EXPLOSION! Never recharge non-rechargeable batteries . Do not short- circuit batteries and / or open them . Overheating, fire or bursting can be the result .

Risk of damage of the product Only use the specified type of battery! Insert batteries according to polarity marks (+) and (­) on the battery and the product . Clean the contacts on the battery and in the battery compartment before inserting! Remove exhausted batteries from the product immediately .

Never throw batteries into fire or water . Do not exert mechanical loads to batteries .
Risk of leakage of batteries Avoid extreme environmental conditions and temperatures, which could affect batteries, e .g . radiators / direct sunlight . If batteries have leaked, avoid contact with skin, eyes and mucous membranes with the chemicals! Rinse immediately the affected areas with fresh water and seek medical attention!

WEAR PROTECTIVE GLOVES! Leaked or damaged batteries can cause burns on contact with the skin . Wear suitable protective gloves at all times if such an event occurs .

Remove batteries if the product will not be used for a longer period .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 7

GB/IE/NI/MT/CY 7
18/01/2022 6:52:37 pm

Parts description

Product:
A
1 [ ] 1[ 1]

8 [ ] 1[ 2]

2 [ ]

3 [ ]

9[ a] 9 [ ]

7 [ ]

4 [ ]

5 [ ] 6 [ ]

1[ 0] [1] USB cap [2] LED indicator [3] Display [4] (stop button) [5] Wall holder [6] Sensor holes

[7] (start button) [8] USB A plug [9] Battery cover [9a] Battery protective sheet [10] Battery compartment [11] Screw [12] Wall plug

8 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 8

18/01/2022 6:52:37 pm

Display:
B

1[ 3] 1[ 4] 1[ 5] 1[ 6] 1[ 7] 1[ 8] 1[ 9] 2[ 0]

2[ 9] 2[ 8] 2[ 7] 2[ 6] 2[ 5] 2[ 4] [13]

(start)

[14]

(stop)

[15]

(minimum value)

[16]

(marking)

[17]

(mean kinetic temperature)

[18]

(number of sets)

[19]

(temperature unit)

[20]

(low battery)

[21]

(humidity unit)

2[ 1] 2[ 2] 2[ 3] [22]

Temperature/humidity reading

[23]

Time display area

[24]

(fixed/time delay symbol)

[25]

(abnormal logging alarm)

[26]

(no alarm)

[27]

(low alarm setting)

[28]

(high alarm setting)

[29]

(maximum value)

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 9

GB/IE/NI/MT/CY 9
18/01/2022 6:52:38 pm

Display overview

D

10 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 10

7. 8. 9. 7. 8.
18/01/2022 6:52:38 pm

Before first use
Insert/change the battery
m ATTENTION! Risk of data loss! All
recorded data is lost when replacing the battery . If necessary, save all recorded data on your computer before replacing the battery .
NOTES: First time use: The battery inside the battery compartment [10] is new . Remove the battery protective sheet [9a] from the battery compartment [10] . Do not press any button while changing the battery . When the battery charge status is low, [20] is shown in the display [3] . A low battery leads to false or inaccurate measuring results . Use a coin to rotate the battery compartment cover [9] in an anti-clockwise direction until a click sound is heard . Remove the battery compartment cover . If required, remove the old battery by lifting it out with a small screwdriver . Insert the new battery under the metal contacts on the edge, with the + polarity facing outwards . Push the battery into the battery compartment [10] . Reattach the battery compartment cover [9] . Use a coin to rotate the battery compartment cover in a clockwise direction .

Mount the wall holder
Mount the wall holder [5] on a wall using the screws [11] and wall plugs [12] .
Display on/off
Remove the protective film from the display [3] . Switching on: Briefly press [7] or [4] to switch on the display [3] . The display [3] switches off automatically after approx . 10 seconds if no button is pressed during this time .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 11

GB/IE/NI/MT/CY 11
18/01/2022 6:52:39 pm

Software installation

System requirements

To install the

Temperature and Humidity Monitor software, the computer should meet

the following minimum requirements:

Pentium 1 GHz processor or faster

RAM memory: Min . 1 GB

Storage capacity on hard disk drive: Min . 2 GB

USB 2 .0/3 .0

Operating system: Microsoft Windows 7 / 10

NOTE: Perform a Windows update first, if your computer does not contain the corresponding Windows version .

Install the software

1 . Download the software from website https://www .lidl-service .com and get the file Setup.exe .

2 . Double-click Setup.exe to start the installation . One or more pop-up warning windows are shown . 3 . Click Yes on all pop-up warning windows to continue .

12 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 12

18/01/2022 6:52:39 pm

4 . Click Next to continue .

5 . Select install location . Click Install to start the installation .

6 . The software is being installed .
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 13

GB/IE/NI/MT/CY 13
18/01/2022 6:52:39 pm

7 . Click Finish to complete the installation . 8 . The Temperature and Humidity Monitor icon is shown on the desktop .

14 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 14

18/01/2022 6:52:39 pm

Launch the software
1 . Double-click the Temperature and Humidity Monitor icon . One or more pop- up windows are shown .
2 . Click Yes on all pop-up warning windows to continue .

3 . Switch off the notifications: Go to Windows Settings . Search User Account Control Settings . Select Never Notice . Confirm by clicking OK .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 15

GB/IE/NI/MT/CY 15
18/01/2022 6:52:39 pm

4 . The following icons are shown on the software interface: Download, History, Export, Parameters, Options, Manual, Exit .
5 . Insert the product into the USB port of the computer . USb is shown on the display [3] . The LED indicator [2] flashes until data is generated . The logger drive folder opens automatically . Users can click the pdf or csv file to check the data .

16 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 16

18/01/2022 6:52:39 pm

Interface and basic functions

After the data is generated, click the Download icon and then click OK to see the full software interface .

1 . Toolbar 2 . Data list 3 . Information and records 4 . Graph and alarm information

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 17

GB/IE/NI/MT/CY 17
18/01/2022 6:52:39 pm

Toolbar

Click Download to download the data .

Click History to display historical data .

Click Export to export data as pdf and xls reports .

Click Parameters to open the dialogue .

Click Manual to open the software manual .

Click Exit to close the software .

Click Language to select your language .

18 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 18

18/01/2022 6:52:40 pm

Parameter 1. Device
2. Time 3. Alarm

Details

Model:

PKDL A1

Unit (temperature unit):

°C or °F

ID:

User can set the ID (Range: 0 to 255)

Description:

Add a description with numbers or letters .

Set the product’s time . NOTE: Choose your country’s “UTC” before setting the time .

If the update option is checked, the time on the computer is set on the product .

Alarm enabled:

If the alarm is triggered, LED indicator [2] flashes in red every 10 s . [25] is shown on the display [3] to indicate abnormal logging alarm .

Mode:

Alarm type, single or accumulate setting menu

Threshold:

High/low alarm limit setting menu

Delay:

Alarm delay time setting menu (0 s to 10 h) NOTE: Time can only be set in multiples of 10 s .

If delay time is 0 s at The LED indicator [2] flashes in red immediately when

single mode:

the measured data exceeds the threshold set limit .

If delay time is >0 s at single mode:

The LED indicator [2] flashes in red when delay time is reached .
NOTE: The product does not alarm if the reading resumes normal within delay time .

Accumulated mode: If accumulated alarm time delay time, alarm is enabled .

Adjust temperature/ Adjust humidity:

This is an adjustment for the entire logged data . Entire logged value is adjusted according to this value .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 19

GB/IE/NI/MT/CY 19
18/01/2022 6:52:40 pm

Parameter 4. Sampling
5. Write Read Close

Details

MAX/MIN/AVG/MKT/ALARM are calculated for the entire logged record .

Interval:

Recording interval setting time (10 s to 24 h) NOTE: Time can only be set in multiples of 5 s .

Delay:

Start logging after the delay time (0 min to 240 min)

Start with:

Start logging option .

Key:

Long press the button to start logging .

Software:

Start logging through software . The product will start logging after the user unplugs the product from the computer .

Appointment:

Start logging at preset fixed time .

Stop with key:

Press and hold the button to stop logging .

Write all parameters’ settings into the product . This setting applies to user’s next time record and does not change the history record data .

Read current product’s parameters .

Close parameters setting .

20 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 20

18/01/2022 6:52:40 pm

Data list This area displays all data download records named by date and time . Double-click the record bar to switch .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 21

GB/IE/NI/MT/CY 21
18/01/2022 6:52:40 pm

Information and records

Click

to show device information/setting/record information/mark record .

Click

to show the temperature and humidity records of every interval time .

If the alarm is enabled, is shown .

Device Information Settings Record information Mark records

Set in toolbar parameters ­ device Set in toolbar parameters ­ sampling Basic information of this record The marking information of this record

22 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 22

18/01/2022 6:52:40 pm

Graph and alarm information

Graph:

The graph area shows the temperature and humidity graph of the entire record .

Move the cursor to the graph, to display the corresponding temperature and humidity value at a

certain point in time .

Show or hide the graph by clicking

in the upper left corner .

The humidity bar gives a more intuitive understanding of the current humidity range .

DRY (orange): Humidity less than 30 %

COMFORT (green): Humidity ranges from 30 to 69 %

WET (blue): Humidity over 70 %

The temperature graph is displayed in yellow colour .
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 23

GB/IE/NI/MT/CY 23
18/01/2022 6:52:40 pm

The humidity graph is displayed in blue colour .

Use the cursor to select a part of the graph . The selected part will be enlarged and displayed .

24 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 24

18/01/2022 6:52:40 pm

Reverse selection at any point on the graph will restore the entire graph .
Alarm: Alarm information: This area shows the alarm information of this record . Threshold/mode/delay: Set in Parameters – Alarm . Duration: Duration alarm Count: Number of alarms . If there is a continuous alarm without any interruption, the count of alarms is one . Status: Alarm or no alarm

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 25

GB/IE/NI/MT/CY 25
18/01/2022 6:52:40 pm

Operation using software

Double-click the

Temperature

and Humidity Monitor icon on your

computer desktop to open the software .

One or more pop-up warning windows is

shown when opening the software . Click

Yes on all pop-up warning windows until the

software is opened .

Pull off the USB cap [1] from the product .

Insert the USB A plug [8] of the product into

the USB port of your computer .

USb is shown on the display [3] and the LED

indicator [2] flashes faster several times until

data is generated .

m ATTENTION! Risk of product damage!
To prevent malfunction of the product/loss of
logged data, do not remove the product from
the USB port until LED [2] stops flashing .

The software does not recognize the product until the LED indicator [2] stops flashing . During this time, the software shows “Disconnected” on the bottom left corner . Once the LED indicator [2] stops flashing, the software shows “connected ID:XXX” on the bottom left corner . The logger drive folder opens automatically . Open the pdf or csv file to check the data . Review software user manual: Open the
Temperature and Humidity Monitor software and select manual . The software user manual offers additional support and exact descriptions of each software function .

Program the product

m ATTENTION! Risk of product damage!
Once the product is reprogrammed, all previously logged values are deleted from the product . If required, save the logged values on your computer prior to reprogramming the product .

Set up the parameters: Open the Temperature and Humidity
Monitor software . Click parameters to open the parameter interface window .

NOTE: Review software user manual: Open

the

Temperature and Humidity

Monitor software and select manual . The

software user manual offers exact descriptions

of each software function and usage .

26 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 26

18/01/2022 6:52:40 pm

Operation Main interface mode
Switch on the display [3]: Briefly press [7] or [4] . The main interface mode (Fig . C3) is shown .

Start/stop logging

Fig . C3
Currently measured temperature [22] and current time [23] are shown on the main interface mode .
Humidity interface mode

Fig . C3

Fig . D5

While the display [3] is at main interface mode (Fig . C3), briefly press [4] to switch to humidity interface mode (Fig . D5) . Currently measured humidity [22] and current time [23] are shown on humidity interface mode (Fig . D5) . Press [4] again to switch back to main interface mode (Fig . C3) .
NOTE: At any interface/display mode: Briefly press [4] 1x to exit and to go back to main interface mode .

Fig . C3

Fig . C9

While the display [3] is at main interface mode (Fig . C3), press and hold [7] until is shown (Fig . C9) .
[13] is shown to indicate that the logging has started . LED indicator [2] flashes every 10 s . While the display [3] is at main interface mode (Fig . C3), press and hold [4] until [14] is shown .
[14] is shown to indicate that the logging has stopped . LED indicator [2] stops flashing .
NOTES: Refer to software user manual for more details about start/stop logging . While logging (measuring temperature/ humidity), never block the sensor holes [6] as it affects the measurement accuracy . For better accuracy, do not keep the product in your hands while logging . Put the product back onto the wall holder [5] .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 27

GB/IE/NI/MT/CY 27
18/01/2022 6:52:41 pm

Maximum temperature

Marked value
NOTE: Marked value function is used for marking measured values for future reference .

Fig . C3

Fig . C5

While the display [3] is at main interface mode (Fig . C3), briefly press [7] 1x to go to maximum temperature mode (Fig . C5) .
[29] and maximum temperature measured for the entire logged period are shown .

Minimum temperature

Fig . C3

Fig . C2

Fig . C3

Fig . C7

While the display [3] is at main interface mode (Fig . C3), briefly press [7] 2x to go to minimum temperature mode (Fig . C7) .
[15] and minimum temperature for the entire logged period are shown .

Fig . D8
While the display [3] is at main interface mode (Fig . C3), press and hold [7] to mark a particular measured data . Marked value flashes 3x simultaneously with [16] and shows the directive number (Fig . D8) at the end of the flash .
NOTES: Max . 10 values can be marked in each logging measurement . All marked values are downloaded to software while downloading all other data . All downloaded marked values are shown in information . All marked values are also shown in the exported pdf file .

28 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 28

18/01/2022 6:52:41 pm

Temperature alarm

Change temperature unit

Fig . C3

Fig . C4

Fig . C3

Fig . C8

Fig . C6
While the display [3] is at main interface mode (Fig . C3), briefly press [7] 4x to see high temperature alarm set value . [28] is shown (Fig . C4) . While the display [3] is at main interface mode (Fig . C3), briefly press [7] 5x to see low temperature alarm set value . [27] is shown (Fig . C6) . If measured temperature exceeded high or low alarm set range, [25] is shown and LED indicator [2] flashes every 10 s in red colour . If measured temperature is within high or low alarm set range, [26] is shown and LED indicator [2] flashes every 10 s in green colour .
NOTE: For more details about alarm settings and functions, refer to software user manual .

Fig . D1

Fig . D3

While the display [3] is at main interface mode (Fig . C3), briefly press [7] 7x to select unit °C/°F [19] (Fig . C8) . Press and hold [7] and [4] button simultaneously for 3 s . The newly changed temperature unit appears on the display [3] . The display [3] switches back to the main interface mode (Fig . C3) .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 29

GB/IE/NI/MT/CY 29
18/01/2022 6:52:41 pm

Maximum humidity

Humidity alarm

Fig . D5

Fig . D7

While the display [3] is at humidity interface mode (Fig . D5), briefly press [7] 1x to go to maximum humidity mode (Fig . D7) .
[29] and maximum humidity measured for the entire logged period are shown .

Minimum humidity

Fig . D5

Fig . D2

While the display [3] is at humidity interface mode (Fig . D5), briefly press [7] 2x to go to minimum humidity mode (Fig . D2) .
[15] and minimum measured humidity for the entire logged period are shown .

Fig . D5

Fig . D4

Fig . D6
While the display [3] is at humidity interface mode (Fig . D5), briefly press [7] 3x . [28] is shown (Fig . D4) . While the display [3] is at humidity interface mode (Fig . D5), briefly press [7] 4x . [27] is shown (Fig . D6) . If measured humidity exceeds high or low alarm set range, [25] is shown and LED indicator [2] flashes every 10 s in red colour . If measured humidity is within high or low alarm set range, the display [3] shows [26] and LED indicator [2] flashes every 10 s in green colour .
NOTE: For more details about alarm settings and functions, refer to software user manual .

30 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 30

18/01/2022 6:52:41 pm

Information

Fig . C3

While the display [3] is at main interface mode (Fig . C3), press 3 seconds to enter information interface . Briefly press [7] to view date . Press [7] again to view product ID . Press [7] again to view remaining storage groups . Press [7] again to view number marking record . Briefly press [4] to go back to main interface mode (Fig . C3) .

[7] and [4] simultaneously for

Troubleshooting

Error The measurement is too high or low .
The display [3] is not reacting .
The display [3] indicator is weak .

Possible causes/solutions
Check whether the sensor holes [6] are blocked by your hand or any other object . If this is the case, remove the block from the sensor holes [6] and put the product back into the wall holder [5] .
Briefly press [4] to enter main interface mode . If required, remove and reinsert the battery to reset the product .
The battery is low . Replace the battery (see “Insert/change the battery”) .

NOTE: Electrostatic discharges can lead to malfunctions . In the event of such malfunctions, remove and reinsert the battery .

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 31

GB/IE/NI/MT/CY 31
18/01/2022 6:52:42 pm

Cleaning and care
Do not allow liquids to enter the product . Otherwise the product may be damaged . Only clean the product with a slightly damp cloth . Before every use: Check the product for visible external damage .
Storage
Always attach the USB cap [1] to the product when not in use . Always remove the battery if the product is not used for extended periods . Store the product at a dry location out of the reach of children .

Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities .
Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1­7: plastics / 20­22: paper and fibreboard / 80­98: composite materials .
The product and packaging materials are recyclable, dispose of it separately for better waste treatment . The Triman logo is valid in France only .
Contact your local refuse disposal authority for more details of how to dispose of your worn-out product .
To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste . Information on collection points and their opening hours can be obtained from your local authority .
Faulty or used batteries must be recycled in accordance with Directive 2006/66/EC and its amendments . Please return the batteries and / or the product to the available collection points .
Environmental damage through incorrect disposal of the batteries!
Batteries may not be disposed of with the usual domestic waste . They may contain toxic heavy metals and are subject to hazardous waste treatment rules and regulations . The chemical symbols for heavy metals are as follows: Cd = cadmium, Hg = mercury, Pb = lead . That is why you should dispose of used batteries at a local collection point .

32 GB/IE/NI/MT/CY
376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 32

18/01/2022 6:52:42 pm

Warranty

The product has been manufactured to strict quality guidelines and meticulously examined before delivery . In the event of product defects you have legal rights against the retailer of this product . Your legal rights are not limited in any way by our warranty detailed below .
The warranty for this product is 3 years from the date of purchase . The warranty period begins on the date of purchase . Please keep the original sales receipt in a safe location . This document is required as your proof of purchase .
Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it ­ at our choice ­ free of charge to you . This warranty becomes void if the product has been damaged, or used or maintained improperly .
The warranty applies to defects in material or manufacture . This warranty does not cover product parts subject to normal wear, thus possibly considered consumables (e .g . batteries) or for damage to fragile parts, e .g . switches, rechargeable batteries or glass parts .

Warranty claim procedure
To ensure quick processing of your case, please observe the following instructions:
Please have the till receipt and the item number (IAN 376306_2104) available as proof of purchase .
You will find the item number on the rating plate, an engraving, on the front page of the instructions for use (bottom left), or as a sticker on the rear or bottom of the product .
If functional or other defects occur, please contact the service department listed either by telephone or by e-mail .
You can return a defective product to us free of charge to the service address that will be provided to you . Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred .
Service
Service Great Britain Tel .: 08000569216 E-Mail: owim@lidl.co.uk Service Ireland Tel .: 1800 200736 Service Northern Ireland Tel .: 0800 0927852 E-Mail: owim@lidl.ie Service Malta Tel .: 80062960 E-Mail: owim@lidl.com.mt Service Cyprus Tel .: 8009 4211 E-Mail: owim@lidl.com.cy

376306_2104_Software_UM_GB_IE_NI_MT_CY_01.indb 33

GB/IE/NI/MT/CY 33
18/01/2022 6:52:42 pm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>