ESR 2C562 HaloLock Mini Wireless Charger User Manual

ESR 2C562 HaloLock Mini Wireless Charger

Thanks for choosing ESR!
To ensure you get the most out of your new charger, read this manual before use. When you’re done, keep it somewhere state in case you need it again.

Using Your Charger

1. This is a magnetic wireless charger that automatically aligns with the wireless charging coil in your iPhone (requires an iPhone with MagSafe or a magnetic phone case).
2. Plug the USB-C cable into a power adapter and magnetically attach the charger to begin charging

Important Reminders

1. The charger only supports magnetic attachment with a caseless iPhone with MagSafe, an official MagSafe case, an ESR HaloLockTM case, or a standard case with a HaloLockTM Universal Ring. It may not attach to other magnetic cases. It will not attach to any other non-magnetic phones or cases. (Over time, the charger may leave a faint circular mark on the back of your phone that can be easily cleaned with an alcohol wipe.)
2. This charger supports input of 9 2A and outputs a maximum of 15W. The maximum output supported by iPhone is 7.5W.
3. For maximum charging speed, use a charging adapter compatible with QC (Quick Charge) 2.0/3.0 or PD (Power Delivery) fast charging.
4. The charger must be connected to a power source to begin wireless charging.

Safety Warnings

1. Do not expose the device to temperatures below 0°C (32°F) or above 60°C (140°F).
2. Do not expose the device to an open flame or submerge it in water as this will damage the device.
3. Always check for damage to the device, cables, or other accessories before using the device. If it is damaged, do not use the device.
4. Do not attempt to disassemble or modify the device in any way, as it may cause serious damage and void the warranty.
5. Do not expose the device to corrosive liquids, or high humidity as they will seriously damage the device and void the warranty.

FCC ID:2APEW-2C562

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible tor compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, it not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment  does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator &your body.

IC:24790-2C562
This device complies with Industry Canada licence-exempt RSS standard( s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.”
   This equipment complies with C RF radiation exposure limits set forth for an uncontrolled environment.
   This equipment should be installed and operated with a minimum distance of I0 centimeters between the radiator and your body.

This product complies with the radio interference requirements ot the European Community.

Declaration of Conformity
This product is intended for use within Europe. Electronic Silk Road Corp. hereby declares that this product 2c562 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU,2014/35/EU,2014/30/EU. The Declaration of Conformity for the 2C562 is available from www.esrgear.com

This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>