ESR ECW5 Wireless Charger User Manual
- June 5, 2024
- ESR
Table of Contents
Wireless Charger
User Manual
Thank you for choosing ESR!
-
After connecting to a power source, the indicator light will turn on for 5 seconds.
For a more efficient charging experience, please use a QC 2.0 or QC 3.0 power adapter. -
After placing your phone on the charging pad, the indicator light will pulse and charging will begin.
• To avoid disturbing you, the indicator light will only pulse for 60 seconds, after which the light will turn off while charging continues.
• If any issue is detected during the charging process the indicator light will flash quickly.
SPECIFICATIONS
Model:
Input:
Output:
Power:
Conversion Rate:
Dimensions:| ECW5-1
DC 5V/2A, DC 9V/1.7A
DC 5V/1-1.5A, DC 9V/1.1A
5W/7.5W/10W (MAX)
70%-80%
101.5 g
99.4mm x 99.4mm x 8.6mm
---|---
IMPORTANT NOTICE
- For a more efficient charging experience, please use a QC 2.0 or QC 3.0 power adapter.
- Please do not place any metallic objects or magnet cards on the charging pad as they may damage or interfere with the charger.
- If during use, the charger overheats and shuts down, please remove your phone and allow the charger to cool before trying to charge your phone again.
- Please ensure that your phone’s case is not thicker than 5mm to avoid interfering with the charging process.
- When charging, be sure to place your phone in the center of the charging pad.
- Please keep the ECW5-1 away from water and other liquids.
SAFETY NOTICE
- Do not pull roughly on the power cord; doing so may damage the power cord.
- Do not disassemble the ECW5-1 or put it into fire or water as this may cause electrical shock.
- Do not use the ECW5-1 in damp, corrosive, or high-temperature environments, as this may damage the circuits or cause electrical shock.
FCC ID: 2APEW-ECW5
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o_ and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator &your body.
IC: 24790-ECW5
This device complies with Industry Canada licence-exempt RSS standard( s).
Operation is subject to the following two conditions: (1)this device may not
cause interference, and (2)this device must accept any interference, including
interference that may cause undesired operation of the device.
http://www.esrgear.com/market/BBJCUS-nHPMTc
ESR Official Website
ESR Page Officielle ESR Offizielle Website Sito Ufficiale ESR Sitio web
oficial de ESR
Facebook@ESRgear
Instagram@ESRgearofficial.esrgear.com