ESR ASCEND Keyboard Case Lite User Manual

June 3, 2024
ESR

ESR ASCEND Keyboard Case Lite User Manual
ESR ASCEND Keyboard Case Lite

Pairing Mode
Long press for 3 seconds to enter Bluetooth pairing mode. If no connection is made within 3 minutes, the device will automatically exit Bluetooth pairing mode.

Auto Reconnect
When turned on, the keyboard will automatically attempt to reconnect with the last paired device for 5 seconds.

Power Light Overview
Charging:
Fully charged:
Low battery:

Standby Mode
The keyboard back light will turn off automatically after 1 minute of inactivity.
Alter 10 minutes of inactivity, the keyboard will enter standby mode. Press any key to wake the keyboard.

Back light
Press to select the backlight brightness (bright medium, low, off).
Press  to select the back light color (7 colors).

Factory Reset
Press and hold for 3 seconds.
Both lights will flash 3 times to indicate a successful reset.

Document Editing
Press to go to of page.
Press to go to bottom of page.
Press to go to star of line.
Press to go to end of line.

Shortcut Keys

Shortcut Keys

 Troubleshooting Guide

If the keyboard stops working, please check the following:

  1. Ensure the keyboard is switched on.
  2. If the keyboard is out of battery, charge the keyboard.
  3. If the connection is unstable, turn the keyboard off and wait 10 seconds before turning it back on. If the problem persists unpair the keyboard by going to Settings> Bluetooth > Device List> “ESR Keyboard” and tap , then choose “Forget This Device. Follow the Bluetooth pairing instructions to reconnect your keyboard.

If the keyboard remains unresponsive, repeat the above steps. If you are still experiencing problems, contact our customer service at esrgear.com/contact- us/

Reminder

This Bluetooth keyboard has a rechargeable battery. When not using the keyboard for an extended period of time, turn the keyboard off using the power switch to prolong battery life.

FCC ID: 2APEW- 6B004

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference. and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are design&d to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:

  • Re,orient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experience radio/TV technician for help.

This product complies with the radio interference requirements of the European Community.

Dedaration of Conformity

This product is intended for use within Europe. Electronic Silk Road Corp. hereby declares that this product 68004 is in compliance with the essential requirements and other relevant provisions of Directive 2014153/EU,2014/35/EU,2014/30/EU. The Declaration of Conformity for the 6B004 is available from www.esrgear.com

This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

Manufacturer. Shenzhen Youcajia Technology Co., LTD
Address: Building A, Shapuwei Dingfeng Science Park. Songgang Town, Baden District. Shenzhen City, Guangdong Province

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals