kvm-tec KT-6936 media4Kconnect KVM Extender over IP Installation Guide

: June 3, 2024
: kvm-tec

Table of Contents

kvm-tec KT-6936 media4Kconnect KVM Extender over IP Installation
media4Kconnect Special with RS232 & sound
MEDIA4KCONNECT IN THE SIMULTANEOUS DOWNSCALING
SYSTEM STATUS
SETTINGS
FEATURES MENU FEATURES
MATRIX SWITCHING SYSTEM
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

kvm-tec KT-6936 media4Kconnect KVM Extender over IP Installation

media4Kconnect Special with RS232 & sound

4K DP 1.2 uncompressed

HAVE FUN – Your kvm-tec Extender is now in use for many years (MTBF approx. 10 years)!

Connect the CON/Remote and the CPU/Local Unit with the supplied 12V 2A power supply.
Now connect the USB cable to a USB socket of your PC and connect the other end of the USB cable to the Local Unit. Connect the keyboard and mouse to the Remote Unit.
Connect the Local and the Remote Unit with a network fi ber cable.
Connect the DP cable to the DP socket of the PC to the DP socket DP/in of the Local device and connect the screen on the remote side with the DP cable.
Connect the Audio cable from PC to Local Extender and connect the Audio cable from Remote Extender to Speaker
Connect the Audio Cable from Microphone to Remote Extender and connect the Audio cable from Local Extender to PC.

MEDIA4KCONNECT IN THE SIMULTANEOUS DOWNSCALING

4K sources can be displayed simultaneously in 4K and with downscaling in Full HD on the remote unit. The output of the stream is done at 4K over 10G bandwidth. Two streams are transmitted simultaneously, so the 4K stream has 9 GBIT and the second stream in Full HD 1 Gbit. The streams can be routed and shared independently and one source can be split to any number of screens. One user has full USB control (keyboard and mouse etc).

USING ON SCREEN MENU

Use the monitor and keyboard to access the main menu. Access to the main menu

Make sure that the extenders, monitors and computer are turned on
Press the Alt gr five times one after the other. The main menu and the overview of the submenus are displayed.
To access a submenu, press the corresponding key or navigate with the arrow keys up and down to the corresponding line and then press Enter key.

SCREEN „OSD menu“
In the main menu you can make the following settings by selecting the corresponding letters:
Press
S System status menu system status/ current status
F Features Menu activated features
L Switching List Switching List
P Sharing List Sharing List
E Login Login
U Update update firmware
G Settings settings

SYSTEM STATUS

By pressing the „S“ key or by selecting the arrow keys, you access the status menu, where you will find information about hardware and software versions, as well as the activated upgrades The menu displays information about the connection, the resolution of the video channel and the USB status. The current Firmware version is displayed in the upper left corner. The link status indicates whether a connection is possible. Video and USB display data transfer status

SCREEN „System Status

1. The current version of the firmware can be downloaded from http://www .kvm-tec.com/de/support. Each update file contains a detailed description of the update process. For further information please refer to the update chapter
2. Connect the USB stick to the CON (REMOTE) Unit (wait a few seconds until the USB stick is connected to the CON Unit).
3. Then open the update menu with the „U“ key.
4. Press the „ U“ key to start the update on the remote (CON) unit.
5. Call the file with „S
6. The firmware is shown on the display under „Configuration found“,
7. Press the „U“ key to start the update on the remote (CON) unit

SETTINGS

By pressing the „G“ key or selecting the arrow keys you will have access to the Settings menu, where you can access all Extender settings

Pressing the „F“ key or selecting the arrow keys, you will access the FEATURES menu, where you can select all the functions and the features

P Point to point Mode on/off
S Matrix Switching Mode
E USB Emulation Mode
U USB Save Feature
V Uncompresed mode
M Unlock Features – redundant oder uncompressed I’m Switching System

MATRIX SWITCHING SYSTEM

Pressing „S“ takes you to the Matrix Switching System configuration. If this function is active, the Multiview Commander and Mouse Glide functions are controlled via the Switching Manager software (see Switching Manager manual). All functions of the switching system can be operated via the Switching Manager software.

With this link you can download the Switching Manager Software Manual downloaden: www.kvm-tec.com/en/support/manual

UNCOMPRESSED MODE
By pressing „V“ you can enable and disable the Uncompressed Mode. Once this function is enabled, the KVM Extender will transmit up to 4K resolution uncompressed and in 10bit color depth. Please note that for this mode you need two 10G fiber lines between the remote and the local unit!

UNLOCK FEATURES REDUNDANT UNCOMPRESSED FOR SWITCHING SYSTEMS

In this menu you can also unlock the „Uncompressed“ and „Redundancy“ feature after purchasing your 4k KVM Extender. Order the unlock code for the desired feature from your supplier by providing the device ID and serial number of the 4k KVM Extender. By typing in the unlock code you unlock the desired feature. After unlocking, activate the desired feature in the feature menu.

ADRESS & PHONE/EMAILS

If you have any questions about our products, please contact kvm-tec or your dealer

kvm-tec electronic gmbh Gewerbepark Mitterfeld 1A 2523 Tattendorf Austria Phone: 0043 (0) 2253 81 912 Email: sales@kvm-tec.com Email: support@kvm-tec.com Web: www.kvm- tec.com

You can find our latest updates and FAQs on our homepage: https://www.kvm- tec.com/support/overview-support/