SUNRICHER 1009TYWi5C 4 in 1 RF Plus WiFi LED Controller Instructions

: June 3, 2024
: SUNRICHER

Table of Contents

4 in 1 RF+WiFi LED Controller
Read User Manual Online (PDF format)
Download This Manual (PDF format)

1009TYWi5C

4 in 1 RF+WiFi LED Controller

Important: Read All Instructions Prior to Installation

Function introduction

SUNRICHER 1009TYWi5C - Function

12V/24VDC Power Input
Common Anode Output(+)
CH1:R/R/WW/1 output(-)
CH2:G/G/CW/2 output(-)
CH3:B/B/WW/3 output(-)
CH4:CW/W/CW/4 output(-)
CH5:WW/NC/NC/NC output(-)
NC = No Connection
“Prog.” button, used to pair or delete pairing with RF remote, to enter WiFi pairing mode
Dial switch for device mode selection, DIM, CCT, RGBW and RGB+CCT 4 modes are available, factory default is RGB+CCT mode
Master/Slave setting jumper

Product Data

No.

| Input Voltage| Output Current| Output Power| Remarks| Size(LxWxH)
---|---|---|---|---|---
1| 12-24VDC| 5x4A| 5x(48-96)W| Constant voltage|

145×46.5x16mm

RF+WiFi LED controller
5 channels 12/24V constant voltage output
Max. 4A output per channel
RF frequency: 434/869.6/916.5MHz
Compatible with universal legacy RF remotes
Waterproof grade: IP20

Safety & Warnings

DO NOT install with power applied to device.
DO NOT expose the device to moisture.

Operation

1. Do wiring according to wiring diagram.

2. Pair the WiFi LED controller to the smart phone or tablet:

Step 1: Download the “TuyaSmart” APP from APP store or google play, and register an account as instructed, then log in the account. Please enable bluetooth on your smart phone in advance.

Tap to run the App.
Tap Sign Up.
Tap Agree.
Select your region and input your email address.
Tap to get verification code.
Log in with the account you registered.
Tap to log in.

Step 2: Short press the “Prog” button 5 times continuously (or reset power of the controller 5 times) to reset the WiFi LED controller and set it to WiFi pairing mode, LED light will blink rapidly, then tap “Add Device” to pair the WiFi LED controller to the smart phone.

Tap to add device.
Tap Lighting.
Tap Light Source (Wi-Fi).
Select the WiFi network the smart phone connected.
Tap to continue.

Step 3: Confirm that the driver is set to pairing mode and LED light blinks rapidly. Connecting starts, the WiFi LED controller will appear on the APP interface once added successfully.

Tick to confirm.
Tap to continue.
Tap to finish adding.

Step 4: You can control the WiFi LED controller through the APP.

Tap to turn off/on the driver, press and hold to enter control interface.

3. Remove the WiFi LED controller from the APP interface.

1009TYWi5C - Operation 15 1009TYWi5C - Operation
17

Tap to enter device edit interface.
Tap to remove.

4. Pair the LED Controller with an RF Remote (please refer to user manual of corresponding RF remote)

Step 1: activate the RF remote by short pressing ON button.
Step 2: select a zone on the RF remote by short pressing the zone number if it is a multi-zone remote.
Step 3: short press “Prog.” key on the LED controller (or reset power 3 times) to set it to RF pairing mode.
Step 4: immediately touch the color wheel or short press any other button except on/off button on the remote.
Step 5: LED lights connected with the controller blinks once to indicate successful pairing.

5. Delete Pairing to RF Remotes

Step 1: press and hold the “Prog.” button for over 3 seconds until the connected LED lights blink, which means the pairing is deleted successfully.

6. Master and Slave Setting:

The receiver has both master and slave functions which can be set with a jumper. Short circuit of the jumper means master function, and open circuit means slave function. Once short circuit the jumper on a receiver, please power off and power on the receiver to enable master function. Setting master and slave enables perfect synchronization of color changing effects.
Set one receiver as master and pair it to any zone of a remote, and this zone shall only have one receiver which works as master. Set all other receivers as slave and pair them to other zones of the remote, and multiple receivers can be paired to each zone. Then choose all zones on the remote and play the color changing effects, the master will send sync signal to the slaves to achieve perfect synchronization. The max. sync distance between the master and any slave is within 30m.