SensorLink 660066005 Sub Gigahertz Radio Module User Manual
- June 5, 2024
- SensorLink
Table of Contents
Operators Manual
SensorLink Sub-Gigahertz Radio Module
Available Stock Codes:
K660-066-005
K660-066-006
Specification
Models
K660-066-005
K660-066-006
Range of Operation
Voltage
Temperature
Relative Humidity
Enclosure
Mounting
Radio
Frequency Zone One
Frequency Zone Two
Frequency Zone Three
Power
Range| 915.53MHz
868.27MHz3.0VDC +/-10%
-30˚C to 60˚C
90% non-condensing
To be mounted on the Host
Board
868.27MHZ
915.53MHz
915.53MHz
< 1 milliwatt
50 feet, 15.24 meters
---|---
Safety Information
The SensorLink Radio Module is designed for use with a suitable universal hot stick mounted device. All precautions appropriate for the transmission power level should be taken.
Overview
The SensorLink Radio Module is only approved for use in SensorLink products
and has been developed for measurement data transfer from a sensor unit to a
remote monitoring device located a short distance away.
The antenna is permanently attached and cannot be modified or removed.
The Sub-Gigahertz frequency is set to be in a non-licensed range.
The host device assemblies are controlled by SensorLink’s ISO-approved
revision and Approved Manufacturer’s Parts List controlled Bills of Material.
FCC and Industry Canada Statements
This device complies with Part 15 of the FCC Rules and contains a license-
exempt transmitter/receiver that complies with Innovation, Science, and
Economic Development Canada’s license-exempt RSS.
Operation is subject to the following two conditions:
- This device may not cause harmful interference and,
- This device must accept any interference, including interference that may cause undesired operation of the device.
Instructions to the User
The user is cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate equipment
This Radio Module complies with FCC 15.249. The Radio Module must be soldered
to a host board, within the host device, which presents the 3.0VDC +/-10%
regulated supply and Module configuration.
The host device must be verified to comply with the FCC part 15b requirements
by a technical assessment or evaluation of the FCC rules.
The FCC and Industry Canada statement above must be included in the host
device’s User Manual.
The host device must display, visible to the end-user, the text “Contains FCC
ID: LM8-660066005, Contains IC: 6462A-660066005” or similar wording that
expresses the same meaning. For example:
Contains FCC ID: LM8-660066005
Contains IC: 6462A-660066005
Antenna integration: The antenna must be soldered to the Module, either directly or via a less than 3” extension wire to allow placement outside of a shielded area. The antenna must not be accessible by the end-user after assembly.
DECLARATION OF CONFORMITY
TRADE NUMBER: SensorLink Corporation
MODEL NUMBER: K660-066-005, K660-066-006
COMPLIANCE TEST REPORT NUMBER: 106048
COMPLIANCE TEST REPORT DATE: 04 April 2022
RESPONSIBLE PART (IN USA): SensorLink Corporation
ADDRESS: 1360 Stonegate Way, Ferndale WA 98248 USA
TELEPHONE: 360-595-1000
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If the unit does cause harmful interference, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving device.
- Increase the separation between the equipment and the receiver.
- Consult an experienced radio/TV technician for help.
I the undersigned, hereby declare that the equipment specified above conforms to the above requirements.
Place: Whatcom County
Date: April 17, 2022| Signature:
Full Name: Tenaya Tinsley
Position: President
SensorLink® Corporation
1360 Stonegate Way Ferndale,
WA 98248 USA
phone: 360/595.1000
fax: 360/595.1001
www.sensorlink.com
---|---
References
- Manufacturer of High Voltage Sensing Instruments | SensorLink Corporation
- Manufacturer of High Voltage Sensing Instruments | SensorLink Corporation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>