SUNRICHER DMX512 Universal RDM Enabled Decoder Instruction Manual
- June 1, 2024
- SUNRICHER
Table of Contents
Universal Series RDM Enabled DMX512 Decoder
70060001
Important: Read All Instructions Prior to Installation
Function introduction
Product Data
No.| Input Voltage| Output Current| Output Power|
Remarks| Size(LxWxH)
---|---|---|---|---|---
1| 12-48VDC| 4x5A@12-36VDC
4×2.5A@48VDC| 4x(60-180)W@12-36VDC
4x120W@48VDC| Constant voltage| 178x46x22mm
2| 12-48VDC| 4x350mA| 4x(4.2-16.8)W| Constant current| 178x46x22mm
3| 12-48VDC| 4x700mA| 4x(8.4-33.6)W| Constant current| 178x46x22mm
- Standard DMX512 compliant control interface.
- Supports RDM function.
- 4 PWM output channels.
- DMX address manually settable.
- DMX channel quantity from 1CH~4CH settable.
- Output PWM frequency 2KHz
- Output dimming curve gamma value from 0.1 ~ 9.9 settable.
- To work with power repeater to expand output power unlimitedly.
- Waterproof grade:IP20.
Safety & Warnings
- DO NOT install with power applied to device.
- DO NOT expose the device to moisture.
Operation
To set desired DMX512 address through buttons, button A is to set “hundreds”
position, button B is to set “tens” position, button C is to set “unit”
position.
Set DMX address (Factory default DMX address is 001)
Press and hold down any of the 3 buttons for over 3 seconds, digital display
flashes to enter into address setting, then keep short pressing button A to
set “hundreds” position, button B to set “tens” position, button C to set
“units” position, then press and hold down any button for >3 seconds to
confirm the setting.
DMX signal indicator (the digit 0 of “hundreds” position of DMX address) :
When DMX signal input is detected, the digit 0 of “hundreds” position of DMX
address will stay solid on. If there is no signal input, the digit 0 of
“hundreds” position of DMX address will blink. Choose DMX Channel (Factory
default DMX channel is 4CH)
Press and hold down both buttons B+C simultaneously for over 3 seconds, CH
digital display flashes, then keep short pressing button A to choose 1/2/3/4,
which means total 1/2/3/4 channels. Press and hold down button A for >3
seconds to confirm the setting. Factory default is 4 DMX channels.
For example the DMX address is already set as 001.
1CH=1 DMX address for all the output channels, which all will be address 001.
2CH=2 DMX addresses , output 1&3 will be address 001, output 2&4 will be
address 002
3CH=3 DMX addresses, output 1, 2 will be address 001, 002 respectively, output
3&4 will be address 003
4CH=4 DMX addresses, output 1, 2, 3, 4 will be address 001, 002, 003, 004
respectively PWM frequency (2KHz)
PWM frequency is fixed @ 2KHz and can not be changed. Choose Dimming Curve
Gamma Value (Factory default dimming curve value is g1.5)
Press and hold down all buttons A+B+C simultaneously for over 3 seconds,
digital display flashes g1.5, 1.5 means the dimming curve gamma value, the
value is selectable from 0.1-9.9, then keep short pressing button B and button
C to select corresponding digits, then press and hold down both buttons B+C
for >3 seconds to confirm the setting. 
Firmware OTA update
You will get this after power on the decoder, it means this decoder supports
firmware OTA update function. This function can be used when there is a
firmware update from the manufacturer, the update can be executed through a
Windows computer and an USB to serial port converter, the converter will
connect the computer and the decoder’s hard wire DMX port. A software
RS485-OTW on the computer will be used to push the firmware to the decoder.
Connect the computer and the decoder through the USB to serial port converter,
if you need to update multiple decoders’ firmware, connect the converter to
first decoder’s DMX port, then connect other decoders to the first decoder in
daisy chain through the DMX port. Please do not power on the decoders.
Run the OTA tool RS485-OTW on the computer, select the correct communication
port “USB-SERIAL” , baudrate “250000”, and data bit “9”, use default settings
for other configurations. Then click “file” button to select the new firmware
from the computer, then click “Open Port”, the firmware will be loaded. Then
click “Download Firmware”, the right side state column of the OTA tool will
show “send link”. Then power on the decoders before “wait erase” displaying on
the state column, the digital display of the decoders will show . Then “wait
erase” will show on the state column, which means the updating starts. Then
the OTA tool starts writing data to the decoders, the state column will show
the progress, once writing data finishes, the digital display of the decoders
will flash , which means firmware updated successfully.
Restore to Factory Default Setting
Press and hold down both buttons A+C for over 3 seconds until the digital
display turns off and then turns on again, all settings will be restored to
factory default.
Default settings are as follows:
DMX Address: 001
DMX Address Quantity: 4CH
PWM Frequency: PF2
Gamma: g1.5
RDM Discovery Indication:
When using RDM to discover the device, the digital display will flash and the
connected lights will also flash at the same frequency to indicate. Once the
display stops flashing, the connected light also stops flashing.
The supported RDM PIDs are as follows:
DISC_UNIQUE_BRANCH
DISC_MUTE
DISC_UN_MUTE
DEVICE_INFO
DMX_START_ADDRESS
IDENTIFY_DEVICE
SOFTWARE_VERSION_LABEL
DMX_PERSONALITY
DMX_PERSONALITY_DESCRIPTION
SLOT_INFO
SLOT_DESCRIPTION
MANUFACTURER_LABEL
SUPPORTED_PARAMETERS
Product Dimension
Wiring diagram
- When total load of each receiver is not over 10A
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>