sunricher SRPY-2305N-10CC100-500 10W Dali DT6 NFC Round LED Driver Instruction Manual

: May 15, 2024
: SUNRICHER

Table of Contents

SRPY-2305N-10CC100-500 10W Dali DT6 NFC Round LED Driver
Function introduction
Product Data
Safety & Warnings
Operation
CLO AND CORRIDOR DIM(CD) FUNCTION INSTRUCTION
Additional Remarks
Product Dimension
Read User Manual Online (PDF format)
Download This Manual (PDF format)

“`

10W DALI DT6 NFC Round LED Driver(Constant Current)

SRPY-2305N-10CC100-500 10W Dali DT6 NFC Round LED Driver

Important: Read All Instructions Prior to Installation

Function introduction

Product Data

Output	LED Channel	1
DC Voltage	3-42V
Current	100-500mA via NFC tool; Min.current gear lower to 0.1mA, default

In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2
Built-in DALI-2 interface, DALI DT6 device
Dimmable LED driver. Max. output power 10W
100-500mA current selectable via NFC program tool. Min.current gear lower to 0.1mA
DALI Address/Group/Scene setting via NFC program tool.
Class Ⅱ power supply, full isolated plastic case
High power factor and efficiency
ON/OFF and Dimming control
Amplitude/CCR dimming, smooth and deep dimming
Compatible with universal DALI masters that support DT6 commands
CLO function for a further upgraded experience
CD(Corridor Mode): auto light on when someone enters
IP20 rating, suitable for indoor LED lighting applications
5 years warranty

Safety & Warnings

DO NOT install with power applied to the device.
DO NOT expose the device to moisture.

Operation

With DALI master

DALI Address
1 DALI address for 1 channel output are assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations.
With NFC Programming devices

Note

Do wiring according to the wiring diagram and power on the DALI system .
Recommend setting parameters without power-on the DALI devices .
Please make sure your mobile phone has NFC function and enable it .

Working with “SR NFC Tool” APP
Step 1: Download the APP (searching “SR NFC Tool” from App Store and Google Play) .
Then open the APP . Note:

Please Make sure that you have enabled NFC function with your mobile phone/ tablet .
Please Make sure that the “NFC position” is matched.
Please do not power on the device before setting.
If you can’t download “SR NFC Tool”. Please contact with us.

Step 2 : Add device, and name it as you wish. Step 3: Unlock device, enter parameters configuring page. Note:

You have to unlock the device then do some settings
Only when the corresponding function is selected, the function interface will be displayed.

Step 4: Few parameter interface, you can choose the setting based on your requirements. Step 5: After setting, please save the selected configuration via NFC and power on the device. Tips

NFC function doesn’t require any power driver.
Many functions can be configured by NFC. Kindly check your desired functions.
All of our DALI drivers are in the best performance within our DALI master/ DALI IoT gateway.

Note: Within Our NFC tech design, you shall probably have one of the largest NFC sensing are The More sensitive you’re able to touch, the more convenient you can have.

CLO AND CORRIDOR DIM(CD) FUNCTION INSTRUCTION

Open APP, and Find the CLO/CD functions
Enter CLO Setting homepage Tips:
Working hours : Ability to calculate the working hours of a single driver.
Corridor dim(CD) function
Enter CD Setting homepage

Tips:

You should select either CD mode or PD mode, but not both.
Under CD mode, you can realize it with normal (3rd party) AC sensor.
Default mode: PD mode.

Additional Remarks

Please make sure your APP version is 1.0.10 or higher.
Please make sure NFC driver’s firmware is available with CLO / CD functions.

Product Dimension

Wiring Diagram

With DALI bus
With PUSH dimmer

AC Push Function

Click the button to switch ON/OFF
Press and hold down the button to increase or decrease light intensity to desired level and release it, then repeat the operation to adjust light intensity to opposite direction. The dimming range is from 1% to 100%.

Operating window Dimming Curve Driver Performance Driver Performance

Expected Lifetime

Module Number	Output current	Ta	30 °C	40 °C	45 °C…	60 °C
SRPY-2305N-10CC100-500	100 – 500 mA	Tc	50 °C	60 °C	70 °C…	85 °C
SRPY-2309N-10CCT100-500	100 – 500 mA	Lifetime	> 100,000 h	> 80,000 h	>
60,000 h	> 40,000 h

The LED driver is designed for a lifetime stated above under reference conditions .
The relation of tc to ta temperature depends also on the luminaire design.
MCB Load Quantity Note:

Those MCB parameters are based on ABB S200 series circuit breakers.
For different brands and models of miniature circuit breakers, the quantity of drivers will have difference.
Please do not exceed the above-mentioned quantity during on-site installation, and the specific load quantity shall be subject to on-site installation.
When the installation environment temperature of MCBs exceeds 30°C or when multiple MCBs are installed side by side, the number of mounted drives will be reduced, which requires recalculation.
Type C MCB’s are strongly recommended to use with LED lighting

Update log