SUNRICHER 65W 2 Channels Zigbee LED Driver Instruction Manual

SUNRICHER 65W 2 Channels Zigbee LED Driver Instruction Manual

65W 2CH Zigbee NFC Enabled LED Driver(Constant Current)

Important: Read All Instructions Prior to Installation

Product Data

Output

| LED Channel| 2
---|---|---
DC Voltage| 6-54V
Current| 500-1500mA via NFC setting; Min.current gear lower to 0.1mA,Default 1050mA
Current Accuracy| ±3%( ±1%@Certain full load) @ full load
Rated Power| Max. 65W

Input

| Voltage Range| 200-240VAC/200-240VDC
Absolute Voltage Range| 176-264VAC/176-280VDC
Frequency Range| 0/50/60Hz
Power Factor (Typ.)| > 0.98 @ 230VAC Full load
Total Harmonic

Distortion

| THD ≤ 6% (@ full load / 230VAC)
Efficiency (Typ.)| ＞90% @ 230VAC full load
AC Current (Typ.)| 0.4A @ 230VAC
Inrush Current (Typ.)| Max. 9.68A at 230VAC; 70μs duration
Leakage Current| < 5mA /230VAC
Standby Power Consumption| ＜0.5W
Anti Surge| L-N:2KV

Control

| Dimming Interface| Zigbee
Dimming Range| 0.01%-100%@ Max current
Dimming Method| Amplitude/CCR dimming
Dimming Curve| Linear/ Logarithmic optional

Protection

| Short Circuit| Yes, remove the fault conditions and re-power the device
---|---|---
Over Current| Yes, remove the fault conditions and re-power the device
Over Temperature| Yes, remove the fault conditions and re-power the device

Environment

| Working Temp.| -25℃ ~ +45℃
Max. Case Temp.| TC=85℃ (Ta=”45℃”)
Working Humidity| 10% ~ 95% RH non-condensing
Storage Temp. & Humidity| -40℃ ~ +80℃, 10% ~ 95% RH

Safety & EMC

| Safety Standards| EN61347-1,  EN61347-2-13
Withstand Voltage| I/P-O/P: 3.75KVAC
Isolation Resistance| I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission| En55015, EN61000-3-2, EN61000-3-3
EMC Immunity| En61547,  EN61000-4-2,3,4,5,6,8,11

Others

| ****

MTBF

| 191350H, MIL-HDBK-217F @ 230VAC full load

and 25℃ ambient temperature

Dimension| 123.9×78.8x30mm (LWH)
Warranty| 5 Years

• Dimmable LED driver, ZigBee device based on ZigBee 0 protocol
• Dimmable LED Max. output power 65W
• 500-1500mA current selectable via NFC program Min.current gear lower to 0.1mA
• Dimming curve/Power on state/Soft start/Soft off via NFC program
• Class Ⅱ power supply, full isolated plastic case
• High power factor and efficiency
• PUSH DIM function enabled
• Able to On/Off and control LED lighting luminaries‘ brightness and color temperature
• Amplitude/CCR dimming, smooth and deep dimming
• ZigBee end device that supports Touchlink commissioning
• Can directly pair to a compatible ZigBee remote via Touchlink
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind 20 zigbee green power switches
• Compatible with universal ZigBee gateway products
• Waterproof grade: IP20, suitable for indoor LED lighting applications
• 5 years warranty

Safety & Warnings

• DO NOT install with power applied to the
• DO NOT expose the device to

Operation–Zigbee Network

1. Do wiring according to connection diagram
2. This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.

3.  Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee

Network)

Step 1 : Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail.
Step 2 : From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
Step 3 : power on the device, it will be set into network pairing mode (connected light flashes twice slowly), thenetwork pairing mode will last until the device is added to a zigbee network

Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.

• TouchLink after both added to a ZigBee network, each device can link with 30 remotes.
• To control by both gateway and remote, add remote and device to network first then
• After TouchLink, the device can be controlled by the linked

5.  Removed from a Zigbee Network through Coordinator or Hub Interface

Factory Reset Manually

Step 1 : Enable Pairing via NFC App or re-power on the device for 5 times continuously .

2) All configuration parameters will be reset after the device is reset or removed from the network.

**** Find and Bind Mode

Step 1 : Re-power on the device (initiator node) 3 times to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation

Learning to a Zigbee Green Power Switch

Step 1 : Re-power on the device 4 times to start Learning to GP switch mode (connected light flashes twice), 180 seconds timeout, repeat the operation.

ZigBee Clusters the device supports are as follows:

Input Clusters

• 0x0000: Basic 0x0003: Identify           • 0x0004: Groups           • 0x0005: Scenes           • 0x0006: On/off
• 0x0008: Level Control 0x0300: Color Control         • 0x0b05: Diagnostics

Output Clusters

• 0x0019: OTA

Function setting Via “SR NFC TOOL

1. Enable the Zigbee NFC drivers enter the pairing mode and add it into the Zigbee
2. Factory Enable the configured Zigbee NFC driver into configuring mode.
3. Besides, you can re-power the device 5 times to enable this section as

Step 3: Unlock device, enter parameters configuring page.

Note

• Do wiring according to the wiring diagram .
• Recommend setting parameters without power-on devices .

2) Please make sure your mobile phone has NFC function and enable it .

Working with “SR NFC Tool” APP
Step 1: Download the APP (searching “SR NFC Tool” from App Store and Google Playstore) .
Then open the APP .

Note : 1. Please Make sure that you have enabled NFC function with your mobile phone/ tablet .

2. Please Make sure that the “NFC position” is
3. Please do not power on the device before
4. If you can’t download “SR NFC Tool”. Please contact with

Step 3: Unlock device, enter parameters configuring page.

Note : 1. You have to unlock the device then do some settings

2. Only when the corresponding function is selected, the function interface will be displayed.

Step 4: Few parameter interface, you can choose the setting based on your requirements

Step 5: After setting, please save the selected configuration via NFC and power on the device.

Wiring Diagram

Application 1 （ Without PUSH

Application 2 （ With PUSH ）

Product Dimension

Operating window

Dimming Curve

Driver Performance

Driver Performance

Module Number

|

Ipeak

|

Twidth

|

Max.quantity of LED Driver per MCB

B10  B13  B16  B20  B25  C10  C13  C16 C20  C25 D10  D13  D16 D20  D25

---|---|---|---

SRP-ZG9105N-65CC500-1500

|

9.68A

|

70μs

|

15

|

20

|

24

|

30

|

38

|

20

|

26

|

32

|

40

|

50

|

22

|

29

|

36

|

45

|

57

SRP-ZG9105N-65CCT500-1500

|

9.68A

|

70μs

|

15

|

20

|

24

|

30

|

38

|

20

|

26

|

32

|

40

|

50

|

22

|

29

|

36

|

45

|

57

Note:

1. Those MCB parameters are based on ABB S200 series circuit
2. For different brands and models of miniature circuit breakers, the quantity of drivers will have
3. Please do not exceed the above-mentioned quantity during on-site installation, and the specific load quantity shall be subject to on-site
4. When the installation environment temperature of MCBs exceeds 30°C or when multiple MCBs are installed side by side, the number of mounted drives will be reduced, which requires

• Type C MCB’s are strongly recommended to use with LED lighting

Update log

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>