SUNRICHER SR-2422NK4-DA2 4 Key Push Button DALI Wall Switch Instructions
- June 4, 2024
- SUNRICHER
Table of Contents
SR-2422NK4-DA2 4 Key Push Button DALI Wall Switch
Instructions
SR-2422NK4-DA2 4 Key Push Button DALI Wall Switch
Important: Read All Instructions Prior to Installation
Function introduction
Product Features
- DALI-2 control device with 4 push buttons according to IEC62386-101, IEC62386-103, IEC62386-301, and IEC62386-332
- Supports feedback functionality, provides 8 LEDs
- Suitable for integration and in combination with DALI-2 compliant central control units
- Multimaster capable, multiple modules can be installed on the DALI- line
- DALI bus powered, no extra power supply required
- Easy configuration via DALI-2 compliant central controller USB interface
- Compatible with universal 55mm frames
Product Data
DALI Interface
Input Type | DALI |
---|---|
Marking | DA, DA |
Input Voltage Range | 12VDC – 22.5VDC (according IEC62368-101) |
Typ. Current Consumption DALI (at 16.5V) | 2mA |
Max. Current Consumption DALI
(Inrush Current at 22.5V)| 10mA
Number of Addresses for DALI Control Gear| DALI
Number of Addresses for DALI Control Devices| 4 programmable push buttons
Number of Feedback LED| 8 programmable LEDs
General Data
Dimensions (L x W x H) | 80mm x 80mm x 26.6mm |
---|---|
Mounting | Wall Mounting or on Conduit Box |
Max. casing temperature Tc | 75°C |
Expected Life Time @Tc | 50,000H |
Protection Class | II in Intended Use |
Protection Degree Housing | IP20 |
Protection Degree Terminals | IP20 |
Function | Configurable |
Start-up Time | <150ms |
Terminals
Connector Type | Push-In |
---|---|
Wire Size Solid Core | 0.2 – 1.3 mm2 (AWG26 – AWG16) |
Wire Size Fine Core | 0.2 – 1.3 mm2 (AWG26 – AWG16) |
Wire Size Using Wire End Ferrule | 0.25 – 1.0 mm2 |
Stripping Length | 9 – 10 mm / 0.35 – 0.39 inch |
Release Connector | Push Button |
Environment Conditions
Storing Temperature | -20°C~+50°C |
---|---|
Working Ambient Temperature | -20°C~+50°C |
Relative Humidity | 8%- 80% |
standards
DALI| IEC62386-101:2014 IEC62386-103:2014 IEC62386-301
IEC62386-332 EN 61547
---|---
EMC| EN 61347EN 50015 / IEC CISPR15-2-11
Safety| EN 61347-1
Markings| DALI-2, CE
Safety & Warnings
- DO NOT install with power applied to the device.
- DO NOT expose the device to moisture.
Application
Integration in a system with a DALI-2 compliant central control unit, push
buttons results in input notifications (event messages)
Application and Function
The DALI Switch can be used as an input device for the integration in DALI-2
compliant central lighting control systems. In this mode, each input
(“instance”) informs about changes by using so-called “input notifications”.
These event messages can be evaluated by other controllers on the DALI-line
e.g. as triggers for commands sent to luminaires. The DALI-Switch provides 4
instances of type 1 (input device – push button).
Instance 1-4: Push Button, Instance Type 1 (according to IEC62386-301, Input
Devices – Push Button)
According to the standard, the following INPUT NOTIFICATIONs are supported:
Event name | Event Information | Description |
---|---|---|
Button released | 00 0000 0000b | The button is released |
Button pressed | 00 0000 0001b | The button is released |
Short press | 00 0000 0010b | The button is pressed and released, without being |
pressed quickly again (in case of double press enabled), or the button is
pressed and quickly released (in case of the double press is disabled)
Double press| 00 0000 0101b| The button is pressed and released, quickly
followed by another button press
Long press start| 00 0000 1001b| The button is pressed without releasing it
Long press repeat| 00 0000 1011b| Following a long press start condition, the
button is still pressed, the event occurs at regular intervals as long as the
condition holds
Long press stop| 00 0000 1100b| Following a long press start condition, the
button is released
Button free| 00 0000 1110b| The button has been stuck and is now released
Button stuck| 00 0000 1111b| The button has been pressed for a very long time
and is assumed stuck.
Additional instance parameters like event filter and event timings (short
timer, double timer, repeat timer, stuck timer) can be configured according to
IEC62386-301.
Push Button Function Label
Push button function labels can be printed and customized, to better indicate
whatever functions are configured to the push buttons. Please contact the
salesperson to ask for the available customizable button function file in
Excel format, which will generate the corresponding label image after
selecting the desired function for each button, just print it and install it
as follows:
Step 1: Remove the white color central cover plate using a sharp tool
such as tweezers.
Step 2: Put the printed label into the central part.
Step 3: Install another transparent central cover plate attached to the
product.
Feedback Functionality
This DALI wall switch supports feedback functionality, feedback is the means
of informing the user about the system state, and the supported feedback type
by the switch is visible feedback using 8 LEDs. The instance number of the 8
LEDs are as follows (according to IEC62386-332, Input Devices – Feedback)
LEDs | Instance number |
---|---|
LED 1 (W) | 0x20 |
LED 2 (W) | 0x21 |
LED 3 (W) | 0x22 |
LED 4 (W) | 0x23 |
LED 5 (R) | 0x24 |
LED 6 (R) | 0x25 |
LED 7 (R) | 0x26 |
LED 8 (R) | 0x27 |
Commands to activate and stop feedback
Command Name | Opcode byte |
---|---|
ACTIVATE FEEDBACK | 0x10 |
STOP FEEDBACK | 0x11 |
Feedback variables and additional commands like feedback active, feedback timing, feedbackActiveBrightness, feedbackActiveColour, feedbackInactiveBrightness, and feedbackInactiveColour can be configured according to IEC62386-332.