sunricher 2305N 40W Dali DT6 NFC Enabled LED Driver Constant Current Instruction Manual

sun richer 2305N 40W Dali DT6 NFC Enabled LED Driver Constant Current

Important: Read All Instructions Before Installation

Function introduction

Product Data

Output

| LED Channel| 1
---|---|---
DC Voltage| 50-220V
Current| 80-400mA via NFC setting; Min. current gear lower to 0.1mA
Current Accuracy| ±3%@ full load
Rated Power| Max. 40W

Input

| Voltage Range| 220-240VAC
Frequency Range| 50/60Hz
Power Factor (Typ.)| > 0.95 @ 230VAC Full load
Total Harmonic

Distortion

| THD ≤ 10% (@ full load / 230VAC)
Efficiency (Typ.)| ＞90% @ 230VAC full load
AC Current (Typ.)| 0.5A @ 230VAC
Inrush Current (Typ.)| Max. 8.65A at 230VAC; 86μs duration
Leakage Current| < 5mA /230VAC
Standby Power Consumption| ＜0.5W
Anti Surge| L-N:2KV

Control

| Dimming Interface| DALI Device Type 6 (DALI consumption < 2mA)/ AC Push
Dimming Range| 0.01%-100%@ Max current
Dimming Method| Amplitude/CCR dimming
Dimming Curve| Linear/ Logarithmic optional

Protection

| Short Circuit| Yes, recovers automatically after the fault condition is removed
---|---|---
Over Current| Yes, recovers automatically after the fault condition is removed
Over Temperature| Yes, recovers automatically after a temperature drop

Environment

| Working Temp.| -25℃ ~ +60℃
Max. Case Temp.| Tc=90℃
Working Humidity| 10% ~ 95% RH non-condensing
Storage Temp. & Humidity| -40℃ ~ +80℃, 10% ~ 95% RH

Safety & EMC

| Safety Standards| EN61347-1,  EN61347-2-13
Withstand Voltage| I/P-O/P: 3.75KVAC
Isolation Resistance| I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission| En55015,  EN61000-3-2,  EN61000-3-3
EMC Immunity| En61547,  EN61000-4-2,3,4,5,6,8,11

Others

|

MTBF

| 191350H, MIL-HDBK-217F @ 230VAC full load

and 25℃ ambient temperature

Dimension| 245x30x21mm (LWH)
Warranty| 5 Years

• In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2
• Built-in DALI-2 interface, DALI DT6 device
• Dimmable LED driver with linear metal housing. Max. output power 40W
• 80-400mA current selectable via NFC program tool. Min. current gear lower to 0.1mA
• DALI Address/Group/Scene setting via NFC program tool
• For luminaires of protection class I and protection class II
• High power factor and efficiency. Non-SELV rated driver
• To switch and dim LED lighting luminaires
• Amplitude/CCR dimming, smooth and deep dimming
• Compatible with universal DALI masters that support DT6 commands
• DALI-251/252/253 Enabled， DALI data inside
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty

Safety & Warnings

• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.

Operation

With DALI master

DALI Address
DALI address for 1 channel output is assigned by the DALI Master controller automatically, please refer to the user manuals of compatible DALI Masters for specific operations.

With NFC Programming devices

Note

1. Do wiring according to the wiring diagram and power on the DALI system.
2. Recommend setting parameters without power on the DALI devices.
3. Please make sure your mobile phone has an NFC function and enable it.

Working with the “SR NFC Tool” APP

1. Step 1: Download the APP (searching “SR NFC Tool” from the App Store and Google Play). Then onen the APP.
   Note: 1. Please Make sure that you have enabled the NFC function with your mobile phone/ tablet

2. Please Make sure that the “NFC position” is matched.

3. Please do not power on the device before setting it.

4. If you can’t download “SR NFC Tool”. Please contact us.

5. Step 2: Add the device, and name it as you wish.

6. Step 3: Unlock the device, and enter the parameters configuring page.
   Note: 1. You have to unlock the device and then do some settings

7. Only when the corresponding function is selected, the function interface will be displayed.

8. Step 4: A few parameter interfaces, you can choose the setting based on your requirements.

9. Step 5: After setting, please save the selected configuration via NFC and power on the device.

Tips

1. The NFC function doesn’t require any power driver.
2. Many functions can be configured by NFC. Kindly check your desired functions.
3. All of our DALI drivers are in the best performance within our DALI master/ gateway.

CLO AND CORRIDOR DIM(CD) FUNCTION INSTRUCTION

1. Open APP, and Find the CLO/CD functions

2. Enter CLO Setting homepage
   Tips
   Working hours: Ability to calculate the working hours of a single driver.

3. Corridor dim(CD) function

4. Enter CD Setting homepage
   Tips:

5. You should select either CD mode or PD mode, but not both.

6. Under CD mode, you can realize it with a normal (3rd party) AC sensor.

7. Default mode: PD mode.

Additional Remarks

1. Please make sure your APP version is 1.0.10 or higher.
2. Please ensure the NFC driver’s firmware is available with CLO / CD functions.

Wiring Diagram

1. With the DALI bus

Product Dimension

1. With single-color LED luminaire
2. With PUSH dimmer

AC Push Function

1. Click the button to switch ON/OFF
2. Press and hold down the button to increase or decrease light intensity to the desired level and release it, then repeat the operation to adjust light intensity to the opposite direction. The dimming range is from 1% to 100%.

Product Dimension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>