SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch Instruction Manual

June 4, 2024
SUNRICHER

ZigBee Wireless Dimmer Switch
Instruction Manual
SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch -
fc

Important : Read All Instructions Prior to Installation

Function introduction

SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer
Switch

Note: This switch supports 2 groups for binding max. 30 lighting devices.
SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - Back
side

Product Data

Protocol ZigBee 3.0
Operation Voltage 3VDC (CR2450)
Transmission Frequency 2.4GHz
Transmission Range (free field) 30m
Protection Type IP20
Dimming Range 0.1%-100%
Dimensions 71.2×71.2×13.6mm
  • ZigBee dimmer switch based on ZigBee 3.0
  • Enables to pair ZigBee lighting devices via touchline commissioning without a coordinator
  • Supports find and bind mode to pair with ZigBee lighting devices
  • Supports 2 groups for binding max. 30 lighting device
  • 2.4 GHz global operation
  • Long battery life mesh technology
  • Transmission range up to 30m
  • Compatible with universal ZigBee Gateway products
  • Compatible with universal single-color ZigBee lighting devices

.ZigBee Clusters Supported by This Remote Are As Follows:
Input clusters:

  • Basic
  • Power Configuration
  • Identify
  • Diagnostics

Output clusters:

• Identify
• Group|  • On/off
• Level control
• Ota
---|---

Safety & Warnings

  • This device contains a button lithium battery that shall be stored and disposed of properly.
  • DO NOT expose the device to moisture.
  • Do not ingest battery, Chemical Burn Hazard
  • This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death
  • Keep new and used batteries away from children.
  • If the battery compartment does not close securely, stop using the product and keep it away from children.
  • If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention

Quick Start (Simplified operation compared to standard operations in the part “Operation”)

SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch -
Touchlink + Add Group

Operation

  1. This ZigBee Dim remote is a wireless transmitter that communicates with a variety of ZigBee compatible systems. This transmitter sends wireless radio signals that are used to remotely control a compatible system.
  2. This ZigBee remote supports 2 groups for binding max. 30 lighting devices and enables to control single color ZigBee lighting devices.
  3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - LED
indicator **Note
  1. After pairing successfully, the remote information will appear on the controller or hub interface.
    2) No remote information will appear on the hub interface if paired to Philips Hue Bridge.
    **
  1. TouchLink to a Zigbee Lighting Device
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch -
TouchLink to a Zigbee Lighting Device Note 1)
    Directly TouchLink (both not added to a ZigBee network), please the first factory reset both the remote and device, each remote can link with max. 30 devices, please make sure the first linked device is always powered on when touching the remote with 2nd device and more devices.
  1. TouchLink after both are added to a ZigBee network, each device can link with max. 30 remotes.
  2. To control by both remote and hub, add both remote and device to the network first then TouchLink, after TouchLink, the device can be controlled by the linked remotes and Zigbee hub together.
  1. Removed from a Zigbee Network through Coordinator or Hub Interface

  2. Factory Reset Manually
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - Factory
Reset Manually

  3. Remove a Touchlink Paired ZigBee Lighting Device
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - Remove a
Touchlink Paired ZigBee Lighting Device

  4. Factory Reset a Lighting Device (Touch Reset)
    Note:
    the device shall be added to a network, the remote added to the same one or not added to any network.
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - Factory
Reset a Lighting Device

  5. Find and Bind a Zigbee Lighting Device
    Note:
    Make sure the device and remote are already added to the same Zigbee network.
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - . Find
and Bind a Zigbee Lighting Device
    Note : Each remote can bind max. 30 lighting devices.

  6. Find and Unbind a Zigbee Lighting Device
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - Find and
Unbind a Zigbee Lighting Device

  7. Clear All Find and Bind Mode Paired Lighting Devices
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - Clear
All Find and Bind Mode Paired Lighting Devices

  8. Setup a Network & Add Devices to the Network (No Coordinator or Hub Required)
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - etup a
Network & Add Devices to the Network
    Step 6:
    Add more remotes to the network as you would like.
    Step 7: Factory reset the lighting devices that you would like then add them to the network, refer to their manuals.
    Step 8: Touch link to pair the added remotes and lighting devices, refer to their manuals. Each remote can link with max. 30 lighting devices. Each lighting device can be linked by max. 30 remotes.

  9. OTA
    The remote supports firmware updating through OTA and will acquire new firmware from the Zigbee controller or hub every 10 minutes automatically.

  10. How to Check Whether the Remote Belongs to a Network or not
    Short press any button, indicator blinking means the remote has already been added to a network. No blinking of the indicator means the remote does not belong to any network.

  11. Battery Power Monitor Function
    The remote will report battery power value to the coordinator under the following situations:
    • When powered on.
    • When short I press both buttons of group 2 simultaneously.
    • When operating the switch to send data packets (over 4 hours since the last operation).
    • When added to the network by a coordinator.

Installation

  1. Remove battery insulator
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - Remove
battery insulator

  2. Install the controller to the wall(2 methods)
    SUNRICHER SR-ZG9001K4-DIM2 70100034 ZigBee Wireless Dimmer Switch - nstall
the controller to wall

Mounting

The key part of this controller is a universal one, especially the rotary standard switch element that can be integrated into numerous frames by different manufacturers as below list:

BERKER S1, B1, B3, B7 glass
GIRA Standard55, E2, Event, Esprit
JUNG A500, Aplus
MERTEN M-smart, M-Arc, M-Plan

CAUTION
Risk of explosion if the battery is replaced by an incorrect type

  • replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
  • leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
  • a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
  • disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

SUNRICHER User Manuals

Related Manuals