Westinghouse 61038 1 Light Mini Pendant Copper Instruction Manual

: June 3, 2024
: Westinghouse

Table of Contents

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
MOUNTING AND WIRING INSTRUCTIONS
CLEANING AND CARE
Appliance specifications – TECHNICAL CHARACTERISTICS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Westinghouse 61038 1 Light Mini Pendant Copper Instruction Manual

WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to place of purchase.

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service. For questions and comments, please visit www.westinghouselighting.eu/contact- us and www.westinghouselighting.de/contact-us

NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1).

MOUNTING AND WIRING INSTRUCTIONS

Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.

Thread mounting screws (A) into the matching holes of mounting bar (B).
Place mounting bar (B) flush against ceiling at desired mounting location. Using outside mounting bar holes as a guide, mark where pilot holes are to be drilled.
Inset two plastic anchors (D) into the pilot holes (for drywall ceiling).
Align outside mounting bar holes with plastic anchors (D) (If applicable). Secure mounting bar (B) into place using wood screws (E).
Select number of stems (C) to install based on desired fixture length, then connect stems (C) if applicable.
Thread fixture wires up through stem(s) (C), swivel (F), and canopy (H) (If applicable).
Thread stem(s) (C) into shade (I) assembly and into swivel (F) (If applicable).
Make an electrical connection by loosening the terminal screws on the terminal block (M) and inserting the live, neutral and ground terminals.
Tighten terminal screws. Make sure there are no stray wires.
Raise canopy (H) to ceiling, allowing mounting screw (A) to protrude through openings in canopy (H) and secure into place with cap nuts (T).
Install the shade (I) and support ring onto the socket and secure with screws or retaining ring, whichever is applicable.
Install lamp (not supplied). (Please do not exceed the maximum capacity recommended on the socket).

CLEANING AND CARE

To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.

Meaning of crossed-out wheeled dustbin:

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact you local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least free of charge.

Appliance specifications – TECHNICAL CHARACTERISTICS

Rated voltage	220-240V~
Rated frequency	50/60 Hz
Rated wattage	E27 Max. 60W
Protection class	CLASS I
IP number	IP20

Distributed by:
Westinghouse Lighting, Krefelder Strasse 562
D-41066 Mönchengladbach / Germany

and Westinghouse are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting
All Rights Reserved.
Made in China
www.westinghouselighting.eu
www.westinghouselighting.de

Logo