rutec 85271 LED Power Supply Unit Instruction Manual

: September 28, 2024
: rutec

Table of Contents

rutec 85271 LED Power Supply Unit
Product Usage Instructions
IMPORTANT SAFETY-/ INSTALLATION INSTRUCTIONS
TECHNICAL DATA
TECHNICAL PRODUCT DIMENSIONS:
DESCRIPTION
WIRING DIAGRAM
INSTALLATION
FAQ
Read User Manual Online (PDF format)
Download This Manual (PDF format)

rutec 85271 LED Power Supply Unit

Specifications:

Input : 100-240V AC
Output : 24V DC, 36W
Dimensions (L x W x H): 96 x 44.5 x 30 mm
Marks and Symbols: CE, RoHS, REACH, SELV, IP20

Product Usage Instructions

Description:
The LED power supply unit 85271 is a non-dimmable power supply on the primary side, which outputs a rectified constant voltage of 24V DC on the secondary side for a maximum power consumption of 36W.

Wiring Diagram:

L 230V AC, 50Hz N PE
V+ V-

Installation:
We recommend using a flexible cable and a maximum connection length of 4.0m for the secondary connection. If using a longer connection cable, ensure the cross-section of the cable is designed to prevent a voltage drop exceeding 0.2V DC to maintain the brightness and color consistency of the LED strip.

IMPORTANT SAFETY-/ INSTALLATION INSTRUCTIONS

Allgemeine Hinweise zur Inbetriebnahme

General notes for installation

Commission a qualified electrician to carry out the installation.
Always ensure that the unit is installed in a location with good ventilation to ensure the correct operating temperature.
Never connect the cables when the unit is switched on.
Check the correctness of the connections and check for short circuits before switching on the voltage.
Please do not carry out any repairs yourself. This will invalidate the manufacturer‘s warranty.

FOR THE INSTALLATION SITE AND THE PRODUCT MUST BE TAKE INTO ACCOUNT:

The product is only suitable for installation in dry indoor areas.
The permissible ambient temperature for the product is -20 to +40° C.
Improper use will destroy the product and we will not accept any guarantee. Therefore, please observe our assembly instructions.

POWER SUPPLY UNITS PER CIRCUIT BREAKER

LS	B10	B16	B25	C10	C16	C25
Stk.	3	5	9	6	9	15

TECHNICAL DATA

Input:	100-240V AC
Output:	24V DC, 36W max.
Ambient temperature	-20 bis +40°C
Psb:	0.00 W
Pno:	0.22 W
Efficiency at full load:	85 %
Tolerance:	±5 %

TECHNICAL PRODUCT DIMENSIONS:

Dimensions (L x W x H): 96 x 44.5 x 30 mm

MARKS AND SYMBOLS

CE-compliant with the applicable European directives
RoHS mark for products that do not contain heavy metals (EC Directive 2002/95/EC)
REACH test mark for products whose chemical components are known, registered and authorized (1907/2006/EG)
Parallel connection
Suitable for through-wiring.
Independent operating device
Safety transformer, short-circuit proof
Safety extra-low voltage
Protection class II (double or reinforced insulated housing)
Protection against contact with foreign bodies ≥20mm.
For indoor use only

DISPOSAL:
Dispose of electrical and electronic equipment in an environmentally sound manner. For more information, contact your local authority.

DESCRIPTION

GENERAL INFORMATION:
The LED power supply unit 85271 is a non-dimmable power supply on the primary side, which outputs a rectified constant voltage of 24V DC on the secondary side for a maximum power consumption of 36W.

WIRING DIAGRAM

INSTALLATION

First, connect the LED strip to the secondary side of the power supply unit. Pay attention to the correct polarity + (anode) and – (cathode).
Connect the primary side of the LED power supply unit to the 230 V AC mains voltage in a de-energised state, observing the five safety rules.
Check that the input and output cables have been connected correctly before switching on the power to operate the LED power supply.

INSTALLATION NOTE:

We recommend a flexible cable and a maximum connection length of 4.0 m for the secondary connection.
With a longer connection cable, design the cross-section of your cable so that the expected voltage drop is ≤0.2V DC to prevent a brightness or colour shift in the LED strip.