Maxxima MRL-S20555 2 Inch and 4 Inch Round 5CCT Slim LED Installation Guide

: September 26, 2024
: Maxxima

Table of Contents

MRL-S20555 2 Inch and 4 Inch Round 5CCT Slim LED
Specifications:
Product Usage Instructions:
Installation Guide:
- FAQ:
Q: What should I do if I encounter bare wires during
Q: Can this product be used with emergency exit fixtures?
Q: What should I do if I am unsure about installing this

MRL-S20555 2 Inch and 4 Inch Round 5CCT Slim LED

“`html

Specifications:

Model: MRL-4.3-4#
Electrical Parameters: 2700K, 3000K, 3500K, 4000K, 5000K

Product Usage Instructions:

Installation Guide:

Turn the power off before installation. Remove the existing
fixture if applicable.
Determine the location and necessary hole cutout diameter using
the supplied table and cut the ceiling hole with the listed
diameter.
Open the driver/junction box cover and remove the appropriate
knockout(s) on the side panel. Install the appropriate cable
clamp(s) (not included) and insert the electrical supply cable
through the cable clamp. Connect the ground wire to the green wire,
hot wire to the black wire and neutral wire to the white wire using
the wire nuts provided.
Place all wiring and connections back into the junction box and
close the cover. Connect the driver/junction box to the light panel
using the connector.
Use the CCT selector switch on the cable above the light to
select the desired color of the light.
Insert driver/junction box through the mounting hole.
Push the spring-loaded clips into the mounting hole upwards and
insert fixture into the cutout. Release the clips and the fixture
will be pulled flush into the ceiling.

FAQ:

Q: What should I do if I encounter bare wires during

installation?

A: Make sure no bare wires are exposed outside
the wire nut connectors. Do not continue installation until all
wires are properly insulated.

Q: Can this product be used with emergency exit fixtures?

A: No, this lamp is not intended for use with
emergency exit fixtures or emergency lights.

Q: What should I do if I am unsure about installing this

product?

A: If you are not qualified, do not attempt
installation. Contact a qualified electrician for assistance to
avoid risks of fire or electric shock.

“`

XXXNBYYJNBTUZMFDPN

2″ & 4″ Round 5CCT Slim LED Gimbal Installation Instructions
The units covered in these instructions are intended for Type IC luminaries.
WARNING / ATTENTION
Risk of fire. Supply conductors (power wires) connecting to the fixture must be rated 90° C. If uncertain, consult an electrician.
Risk of electric shock. Luminaries installation requires knowledge of luminaries electrical systems.
Risk of fire or electric shock. If not qualified, do not attempt installation. Contact a qualified electrician.
Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
This lamp is not intended for use with emergency exit fixtures or emergency lights.
CAUTIONS
For your safety, read and understand instructions completely before starting installation. Before attempting installation, check your local electric code, as it sets wiring standa rds
for your locality.

NOTES
If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire is connected to the switch. DO NOT connect the white supply wire to the switch.
Make sure no bare wires are exposed outside the wire nut connectors. Do not make or alter any open holes in an enclosure of wiring or electrical comp onents
during kits installation.

Hole Cutout Diameter

Model
MRL-4
.3-4# MRL-4
.3-4#

)PMF$VUPVU%JBNFUFS JODIFT
p

)PMF$VUPVU%JBNFUFS NN

Parts List

Electrical parameters:

Model

%SJWFS+VODUJPO#PY *OQVU7PMUBHF 7

MRL-S
.3-4# MRL-S41255, MRL-S4#

*OQVU’SFRVFODZ )[

*OQVU$VSSFOU

”

*OQVU8BUUT 8

Installation Guide:
Turn the power off before installation. Remove the existing fixture if applicable.
2. Determine the location and necessary hole cutout diameter using the supplied table and cut the ceiling hole with the listed diameter (Fig.1).
3. Open the driver/junction box cover and remove the appropriate knockout(s) on the side panel (Fig. 2). Install the appropriate cable clamp(s) (not included) and insert the electrical supply cable through the cable clamp. Connect the ground wire to the green wire, hot wire to the black wire and neutral wire to the white wire using the wire nuts provided.

4. Place all wiring and connections back into the junction box and close the cover. Connect the driver/junction box to the light panel using the connector (Fig. 3).
5. Use the CCT selector switch on the cable above the light to select the desired color of the light.
6. Insert driver/junction box through the mounting hole (Fig. 4).
7. Push the spring loaded clips into the mounting hole upwards and insert fixture into the cutout. Release the clips and the fixture will be pulled flush into the ceiling (Fig 5).

Fig. 1

Fig. 2
Cable to Fixture

Black (Hot) Wires

White (Neutral) Wires

FFiigg. . 33

Fig. 4

Fig. 5

Ground Wires
Supply Wire (connector not included)

Junction Box

Floating Gimbal

Three Year Warranty:

2700K