Altronix T2MK7F4D 4 Door Kit with PTC Outputs Installation Guide

**Access & Power Integration

**

T2MK7F4D 4-Door Kit with PTC Outputs

T2MK7F4D
4 Door Kit with PTC Outputs
The fully assembled kit includes:
– Trove2 enclosure with TM2 Altronix/Mercury backplane
– One (1) eFlow104NB – Power Supply/Charger
– One (1) ACM4CB – PTC Protected Access Power Controller
– One (1) PD8ULCB – PTC Protected Power Distribution Module
– One (1) RSB1 – Rocker Switch Bracket with one Rocker Switch

Installation Guide

All components of this Trove kit are UL Listed as sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

All registered trademarks are the property of their respective owners.

Rev. 041020
Installing Company: _____ Service Rep. Name:

Address: __Phone #: _____

Overview:

Altronix T2MK7F4D Trove Mercury kit is pre-assembled and consists of a Trove2M2 enclosure with factory-installed Altronix power supply/charger and sub-assemblies. T2MK7F4D kit also accommodates various combinations of Mercury boards for up to four (4) doors in a single enclosure.

Configuration Chart:

Altronix

Model Number

| 120VAC
60Hz
Input Current (A)| Power Supply Board Input Fuse Rating| Power Supply Board Battery Fuse Rating| Nominal DC Output Voltage| Maximum Supply Current for Main and Aux. Outputs on Power Supply Board| ACM4CB
Board Input Fuse Rating| ACM4CB
Board Output PTC Rating| PD8ULCB
Board Output PTC Rating
---|---|---|---|---|---|---|---|---
[DC]| [Aux]
Output Range (VDC)| Output Range (VDC)
T2MK7F4D| 4.5| 6.3A/| 15A/| 20.19-| 20.19-| 24VDC @ 9.2A| 10A/32V| 2A| 2A
250V| 32V| 26.4| 26.4

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
The product is intended for indoor use only.

1. Remove the backplane from the enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top two/three keyholes in the enclosure. Install two/three upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two/three upper screws; level and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two/three upper screws. Install the three lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in the desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2).
   Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate the alarm signal open the door of the enclosure.

4. Mount Mercury modules to the backplane(s), refer to page 3.

5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow104NB and corresponding Sub-Assembly Installation Guides for ACM4CB and PD8ULCB for further installation instructions.

Hardware:

T2MK7F4D: Configuration of Mercury Boards:

1.  Fasten snap-on spacers onto metal pens configuration (A), (B), (C), or (D) of the backplane depending on the access controller (Fig. 2, pg. 3).
2. Position the access controller module over the corresponding spacers and depress it onto snap-on spacers (Fig. 2a, pg. 3).
3. Mount the backplane to the enclosure with hardware.

Access Controller Position Chart for the Following Models:

Trove2 Enclosure Dimensions (H x W x D approximate):
27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm)

Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA
phone: 718-567-8181
fax: 718-567-9056
web site: www.altronix.com
e-mail: info@altronix.com
Lifetime Warranty
IIT2MK7F4D I29U T2MK7F4D

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>