ESR 6C005 Geo Digital Pencil User Guide
- September 20, 2024
- ESR
Table of Contents
ESR 6C005 Geo Digital Pencil
6C005
Instructions
- Power on: Press top button for 2 seconds till the light on.
- Charging: Charge using USB-C port.
Indicator Light Guide
- Working Status: Solid blue light
- Low Battery: When battery level drops below 10%, blue light flashes.
- Charging Status: Flashing blue light when charging; blue light stays on for 30 seconds when fully charged then turns off.
- Pairing Mode: Automatically enters pairing mode after startup. In iPad settings, go to Bluetooth and select “ESR Geo Digital Pencil” to connect.
- Button Functions: After Bluetooth pairing, single-click to return to the home screen; double-click to open the multitasking view.
Safety Instructions
- Do not store the product below – 10°C or above 35°C.
- Avoid exposure to fire, water, or rain.
- Inspect the product before use, and do not use it if there’s damage.
- Do not disassemble or modify the product. Avoid using sharp objects on the digital pencil.
- Do not use it in high-temperature, humid, or corrosive environments to avoid a warranty void.
FIND MY SECTION
Preparation:
- iPad with iOS 14.5 or later and “Two-Factor Authentication” enabled.
- Enable “Find My”: Go to Settings > Your Name > Find My > Turn on “Find My [Device]”
- Enable Bluetooth connection.
- Wi-Fi or cellular data network connection must be strong
- Enable “Location Services”: Go to Settings > Privacy > Turn on “Location Services”.
Pairing Instructions
- Ensure your device meets ‘Preparation’ requirements, then power on digital pencil.
- On your iPad: Navigate to ‘Find My’ > Items > Add Item > Other Supported Item
- When ‘ESR Geo Digital Pencil’ is found, tap ‘Connect’.
- Select ‘Name Item’, then enter a ‘Custom Name’ to name your digital pencil and choose an ‘Emoji’. Tap ‘Continue’
- To link with your Apple ID, tap ‘Agree’. 6. Complete pairing by tapping ‘Finish’.
Do not exit Find My app when pairing. Restart digital pencil if not connected within 3 minutes.
Locating the Capacitive Pen
Locating the capacitive pen on the map
- Open ‘Find My’ app.
- Select ‘Items’ tab.
- Tap item to locate it on the map.
- Tap ‘Directions’ to view location of digital pencil on map.
Playing Sound
- Open ‘Find My’ app.
- Select ‘Items’ tab.
- Tap item, then tap ‘Play Sound’.
Sound will play once it reconnects or when within Bluetooth range (approximately 50 meters). In offline mode, sound cannot be played and connection to the network is required.
Marking the Digital Pencil as Lost or Enabling Lost Mode
- Open the ‘Find My’ app and select the ‘Items’ tab.
- Tap the lost item.
- Scroll down to ‘Mark as Lost’ or ‘Lost Mode’, then select ‘Activate’ or ‘Enable’.
- Follow the on-screen instructions to display contact information or to customize a message.
Removing the Digital Pencil
- Open the “Find My” app, then tap “Items” tab.
- Select digital pencil. 3. Scroll down and tap “Remove Item”.
Ensure the digital pencil is connected to remove it. If disconnected, manually clear the pairing data (press and hold the top of the digital pencil for 20 seconds until you hear a beep, then release it to clear the pairing data).
FAQ
-
Q: Unable to connect to Find My?
A:- Please ensure that all preparation steps are completed
- Restart the digital pencil if pairing fails.
-
Q: The digital pencil is on but is not functioning?
A: Remove the pairing information for any Apple Pencil if connected to an iPad.
FCC ID
2APEW- 6C005 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
- If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition
IC: 24790- 6C005 This device complies with Industry Canada licence-exempt RSS
standard( s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.” The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Declaration of Conformity
This product is intended for use within Europe. Electronic Silk Road Corp. hereby declares that this product 6C005 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU,2014/35/EU,2014/30/EU. The Declaration of Conformity for the 6C005 is available from www.esrgear.com
- Product name: ESR Geo Digital Pencil
- Model: 6C005
- Input:5V 200mA
- Brand: ESR
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>