ET2 E21720 Handler Outdoor LED Spot Light Installation Guide
- September 17, 2024
- ET2
Table of Contents
ET2 E21720 Handler Outdoor LED Spot Light
Before Getting Started
- Read the instructions carefully prior to assembling the product.
- When you open the package with a sharp tool like a box knife, be careful not to damage the components inside.
- Carefully remove all packaging materials and retain for future use.
- Keep all hardware parts and packaging out of reach of children.
- Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
- Ensure that you have all the required contents for complete assembly.
- Take care when lifting. Assemble the product in close proximity to where you intend to install it.
- Do not over tighten the screws and bolts as this may damage the threads.
- Do not let children play with this product.
Risk of suffocation!
Keep packaging materials away from children.
PARTS
Before getting, started, ensure the package contains the following components
Lamp Care Instructions
Carefully read through the instruction sheet before assembly and using the product.
Caution there is a risk of shock!
- Disconnect from power source before assembling or cleaning.
- Switch off, unplug and allow bulb to cool before replacing bulb or cleaning.
- Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire.
- Check the product cord to be sure is free torn or frayed.
WARNING : Wires must to be connected to low voltage driver and should not be connected directly to live wire or a short may occur.
WET LOCATION : For outdoor use, caulk around EXTERIOR fixture with silicone sealant to prevent water intrusion.
Cleaning & Maintenance
- On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
- For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, stone polish, & wood polish.
- Clean with soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
- Periodically (every 90-180 days) make sure that the screws are fully tightened.
- Prolonged exposure to heat sources may cause glazing, melting and scorching, or even cause color to fade.
ASSEMBLY
This fixture is equipped with an LED driver, please refer to the Wiring Diagram for more details
For outdoor use, caulk around fixture with silicone sealant to prevent water intrusion. Leave a gap at the bottom to allow moisture to escape.
WIRING DIAGRAM
DIMMER COMPATIBILITY
ITEM/MODEL : E21720
MUST be installed by an experienced professional CRITICAL KNOWLEDGE of
electronic lighting systems is required IMPROPER WIRING and/or INCORRECT
DIMMER use can cause CATASTROPHIC DAMAGE!
THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH DO NOT CUT FACTORY-MADE CONNECTIONS.
VERIFIED LIST OF TESTED DIMMERS
- Lutron Diva DVCL-153P
- Lutron Diva DVELV-300P
- Lutron Diva Caseta PD-6WCL
- Lutron Maestro MACL-153M
- DEAKO-Smart Dimmer
- DEAKO-Single Dimmer
- LEVITON 6672-L
- LEVITON DSL06
GENERAL COMPATIBILITY
- TRIAC / FORWARD PHASE
- ELV / REVERSE PHASE
- Only at 120VAC
- 0-10V/ LOW VOLTAGE
- Work at 120-277VAC
- Due to inrush current, wattage should not exceeed 150W on a 600W dimmer
IMPORTANT!
If the control is not paired properly to LED fixtures, irreparable damage may
occur. If the dimmer you are using is not listed here,consult a lighting
professional or view our Dimming Compatibility Chart online:
www.et2online.com/led-dimmer
MUST be installed by an experienced professional CRITICAL KNOWLEDGE of electronic lighting systems required
© 2024 ET2 CONTEMPORARY LIGHTING
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>