ET2 E31250 IQ 24 Ceiling Lamp Instruction Manual
- June 2, 2024
- ET2
Table of Contents
ET2 E31250 IQ 24 Ceiling Lamp
INSTRUCTION MANUAL
ITEM NUMBER: E31250
DESCRIPTION: IQ 24″ Ceiling Lamp
PLEASE CONSULT AN ELECTRICIAN BEFORE INSTALLATION
LAMPING: CCT RGB LED LED INTEGRATED 40W
Vin put: 120-277V
MADE IN CHINA / HECHO EN CHINA/ FABRIQUE EN CHINE
LED Lighting
Before Getting Started
- Read the instructions carefully prior to assembling the product.
- When you open the package with a sharp tool like a cutter knife, be careful not to damage the components inside.
- Carefully remove all packaging materials and retain for future use.
- Keep all hardware parts and packaging out of reach of small children.
- Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
- Ensure that you have all required contents for complete assembly.
- Take care when lifting. Assemble the product in close proximity to where you intend to position the item.
- Do not over tighten the screws and bolts as this may damage the threads.
- Do not let children play with this product
WARNING : Risk of suffocation! Keep any packaging materials away from children.
Lamp Care Instructions
- Carefully read through the instruction sheet before assembly and using the product.
- Caution there is a risk of shock. Disconnect from power source before assembling or cleaning.
- WARNING: Wires need to be connected to driver found in canopy and should not be connected directly to power source or a short may occur.
- Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire.
- Do not plug the product in if cord is torn or frayed.
Cleaning & Maintenance
- On polished finishes, often using talc powder reduces the appearance of fingerprints and other smudges
- For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, acrylic polish, and wood polish.
- Clean with soft cloth and a mild detergent. DO not use abrasive cleaner
- Periodically (every 90 days) make sure that the screws are fully tightened.
- Prolonged exposure to heat sources may cause glazing, melting and scorching, or even cause color to fade.
Contents
Before getting, started, ensure the package contains the following components:
1. INSTALLATION
WIRING DIAGRAM (ONLY FOR REFERENCE)
DO NOT ATTEMPT TO CUT FACTORY CONNECTIONS WITHOUT QUALIFIED KNOWLEDGE. MODIFICATIONS MADE TO THIS PRODUCT WITHOUT THE CONSENT OF THE MANUFACTURER WILL VOID WARRANTY.
NOTE: Notice the wiring diagram and wire color when connecting wires between Wiz controller and LED source
STEP 1. DOWNLOADING THE WiZ APP
Make sure you’ve properly installed your light fixture prior to syncing device. Download the WiZ App from Google Play or the Apple App Store. (IF YOU HAVE NOT YET INSTALLED YOUR LIGHT, INSTRUCTIONS CAN BE FOUND IN THE PRIOR PAGES TITLED “ASSEMBLY INSTRUCTIONS.”)
NOTE: The WiZ app MUST CONNECT TO A 2.4GHz Wi-Fi NETWORK IN ORDER TO PAIR YOUR LIGHTS.
NOTE: Please allow up to 1 minute after initial startup, for fixture to pair.
TROUBLESHOOTING
The following importer is the responsible party:
LLC Sales, Inc. DBA Liteline USA
1209 Orange Street, Wilmington, DE, 19801
Liteline.com/contact-us
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference recieved, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the resposible party could void the user’s authority to operate the equipment.
Note : This equipment has been tested to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) reorient or relocate the receiving antenna; (2) increase the separation between the equipment and receiver; (3) connect the equipment into an outlet on a circuit different from that to which the receiver is connected; consult the dealer or an experienced radio/TV technician for help.
RF Exposure Requirements:
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20cm from all persons.
ISED Canada Compliance Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Déclaration de Conformité ISDE Canada
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement Économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage; et (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Specifications:
- Product Type: LED Lighting (DC Power)
- Power Source: DC
- Recommended Bulb Type: LED bulbs
- Maximum Wattage: Refer to product specifications
FAQ:
Troubleshooting:
Problem: Unable to find light fixture on the network
Solution: Check Wi-Fi connection and ensure proper pairing following instructions.
Problem: Unable to operate light fixture with connected light
switch
Solution: Ensure proper wiring and connection between the light fixture and switch.
Problem: Lights not responding to WiZ APP control
Solution: Check Wi-Fi connection, app settings, and device compatibility.
Problem: Lights not connecting to the WiZ APP
Solution: Restart the app, check Wi-Fi network, and follow pairing instructions carefully.