CG MOBILE SP-V27 Wireless Headphones User Guide
- July 22, 2024
- CG MOBILE
Table of Contents
CG MOBILE SP-V27 Wireless Headphones
Specifications
- Product: Wireless Headphones
- Model: SP-V27
- Charging Port : Yes
- Audio Port : Yes
- Bluetooth: Yes
- Voice Assistant Compatibility : Siri/Google Now
- FCC ID : 2A7J2-BH3DN
Product Operation
Bluetooth Pairing:
- Press and hold the button for 3 seconds to enter pairing mode.
- Activate Bluetooth on your device and select ‘SP-V27’ from the list of available devices.
- Once paired successfully, the blue light will flash slowly every 5 seconds.
Power On and Power Off:
- To power on, press and hold the button for 3 seconds.
- To power off, press and hold the button for 3 seconds.
Bluetooth Music Play:
- Open the music player, and press the button to play/pause music.
- To adjust volume, short press the button to increase/decrease volume.
- To change tracks, press and hold the button for 2 seconds.
Bluetooth Phone Call:
- To answer an incoming call, press the button. Press again to end the call.
- To reject a call, press and hold the button for 2 seconds.
Active Voice Assistant:
Double-press the button to activate the voice assistant (Siri/Google Now).
Charging:
When connected to a charger, the headphone will indicate a red light. The indicator turns off when fully charged.
FAQ
- Q: How do I know if the headphones are fully charged?
- A: The indicator light will turn off when the headphones are fully charged.
- Q: Can I use voice assistants with these headphones?
- A: Yes, you can activate voice assistants like Siri or Google Now by double-pressing the button.
Description
Content
Product Specification
- Bluetooth version : V5.3
- Transmit distance: 10 meter
- Battery: 3.7V / 300 mAh
- Input: DC 5V / 500 mA
- Charging Time : 1.5-2 hours
- Playback Time : 30 hours
- Driver Unit : 40mm
- Sensitivity: 109±3 dB
- Impedance: 32 ohm±15%
- Frequency: 20hz-20Khz
Product Operation
Bluetooth Pairing:
-
For the first pairing, press and hold the button for 3 seconds, the headphone will indicate Bule light for 2 seconds and enter into pairing mode, and then the light will flash in Red and Blue quickly.
- Activate the Bluetooth function on your Bluetooth device (phone or music device). Please refer to the manufacturer’s instructions for instructions on enabling Bluetooth on your device. Once you have activated Bluetooth on your device, select the headphone ‘SP-V27’ from the list of available Bluetooth devices.
- When the pairing is successful, a Blue light will flash slowly every 5 seconds and your device will show the connected Bluetooth icon.
Note: The pairing function can be different from device to device (check the manual of your device) .
-
Power on and Power off:
- Power on – Press and hold the button for 3 seconds.
- Power off – Press and hold the button for 3 seconds.
-
Bluetooth music play:
-
Open the music player, select a song to play, press the button to play music, and then press again to pause music.
-
Play music and short press+ the button to increase the volume, and press and hold for 2 seconds to change the next song.
-
Play music and short press – the button to decrease the volume, press and hold for 2 seconds to change the previous song.
-
Bluetooth phone call:
-
Press the button to answer an incoming call, and press the button again to end the call.
-
When the call is coming, press the button for 2 seconds to reject the call
-
Active Voice Assistant
Double press to active voice assistant ( Siri/Google Now… ).
Charging
When the Bluetooth headphone is connected with a charger (or computer USB port) by charging cable, the headphones will indicate a Red light. When the headphone is fully charged, the indicator will be off.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equitation into an outlet on a circuit it receives. from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Designed in France and made in China.
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for ba Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>