Tribit BTH96 C2 Wireless Ear Buds User Manual

Tribit BTH96 C2 Wireless Ear Buds

Package Contents

1. Earbuds(L/R)
2. Charging Case
3. USB-C Charging Cable
4. User Manual

Product Parts

How to Wear the Earbuds

• To Wear
  
  Place the earbud in your ear canal and rotate it until comfortable.

• To Call

Aim the microphone at the mouth for a better call effect.

• To Pick & Place
  

Power ON I Power OFF

• For the first time use, please tear off the insulation sticker.

• To power On: Open the charging case

• To power Off: Close the charging case

Bluetooth Connection Instructions

Connect the earbuds to a Bluetooth device:

Open the charging case and the earbuds will automatically enter the Bluetooth pairing mode, then the earbuds’ indicator lights will flash alternately red and white. Turn on the Bluetooth function in the Bluetooth device, refresh the Bluetooth device listing, then select the paired audio device named “Tribit FlyBuds C2” to connect. The indicator lights of the earbuds will go off after it connects successfully.

Connect the earbuds with other devices:

Method l: Please disconnect the earbuds with the currently connected Bluetooth device, and the earbuds will automatically enter Bluetooth pairing mode.

Method 2: Tap either earbud for 4 times. When the white indicator light goes on, touch and hold the earbud for 3 seconds. When the indicator lights of both earbuds flash in red at the same time, the earbuds will automatically enter Bluetooth pairing mode.

Touch Control Instructions

playing) and the red light will flash for ls with the power-off prompt tone: Power OFF
Power On| Touch and hold the left and right earphones for 6s and the white light will flash for 6s with the power-on prompt tone: Power ON

Charging Instructions

When the earbuds’ indicator lights flashes in red slowly, please charge the earbuds in time.

• To charge the earbuds: Put the earbuds into the charging case and close the case to start charging. The indicator lights on the far left and right of the charging box show the charging status of the each earbud. During charging, the indicator lights will be always on and will go off after the earbuds are fully charged.
• Charging time of the earbuds: about 90 minutes Open the tor. cover of the charging case and it’ll display its battery leve . When the battery_runs out, the indicator light of the charging case will be off. Please charge the case in time.
• To charge the charging case: Plug one end of the USB cable into a SV power supply, ana the other end into the charging port of the charging case for charging. The indicator lights will flash during the charging process, and the 4 indicator lights will stay on when the earbuds are fully charged.
• Charging time of the charging case: about 90 minutes
  *The above data comes from Thousandshores Laboratory. Thousandshores reserves all rights for final explanation.

How to Reset the Earbuds

Please ensure the 2 earbuds are powered on and disconnected from other Bluetooth-enabled devices before resetting.

Step 1: Tap both earbuds for 6 times simultaneously and quickly, and the LED indicator on both will glow white sturdily. (If you do this with earbuds being worn, you will hear a prompt sound after completing this step.)
Step 2: Double tap both earbuds again within lOs and the LED indicator on both will glow red and white alternately for several times and then will turn off. (If you do this with earbuds being worn, you will hear a prompt sound after completing this step.)
Step 3: After that, the LED indicator of both earbuds will flash white quickly to indicate they are being reset. Please move them closer to each other. After the LED indicators stop flashing, the earbuds have been reset successfully.

Note: After resetting, if there is a Bluetooth device that has been connected to the earbuds, you need to delete the pairing record to allow the earbuds to be paired again.

Frequency band & Maximum transmission power

Frequency band: 2402-2480MHz
Maximum transmission power: -6 -+4d8m

Warning

1. Do not dismantle or modify the earbuds for any reason, otherwise any malfunction of the earbuds is not covered by the warranty.
2. Do not deliberately contact the earbuds to liquids, which may damage the earbuds may be damaged and the warranty turns invalid.
3. Do not place the earbuds in the environment where the temperature is too high or too low (above 45 C or below -20 C ).
4. This product includes a built-in lithium battery. It is forbidden to disassemble, bump, squeeze or throw the product into fire.
5. Please keep the earbuds away from children to avoid accidental swallowing and other injuries.

Important Notes

1. Under noisy environment, the voice from the earbuds will sound lower than the actual volume.
2. Listening to music with high volume for a long time may cause permanent damage to your hearing.
3. Please use the charging cable and power adapter or computer to charge the earbuds. When charging. only use the adapter that comply with the national/regional regulations and international and regional safety standards.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.

Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries.

Customers Support

Hereby, [Thousandshores Deutschland Gmb HJ declares that the radio equipment type [True Wireless Earbuds BTH96] is in compliance with Directive 2014/53/EU. The full text of the EU declaration conformity is available at the following internet address: http://files.tribit.com/bth96-eu-doc.pdf

IS 13252(PART 1):2010

R-41189855
www.bis.gov.in 
Charging case Mark

IS 616:2017

R-41195839
www.bis.gov.in
Wireless Earbuds Mark

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>