LIGHTMEN A75050 Uplight RGBW IP Battery User Manual

LIGHTMEN A75050 Uplight RGBW IP Battery

INTRODUCTION

APOLLO is a compact, high-power, outdoor-rated, cable-free, battery-powered LED uplight with onboard wireless DMX, infrared remote, and manual control via OLED function menu + Six-unit road-worthy custom charging case.

FEATURES

• 4 x 10 W RGBW LED
• 8 hours continuous battery-powered operation at full output, 20 hours with single color
• Onboard wireless DMX
• 3-channel Hue-Saturation-Value and Hue-Saturation-Intensity modes
• Ultra-linear dimming technology for flawless color mixing
• Patented structural design delivers superior passive cooling
• High frequency 1200 Hz LED modulation for flicker-free output
• Adjustable white balance
• IP65: Designed for both indoor and outdoor use
• Patented structural design delivers superior passive cooling
• Charging station in rugged touring case holds 6 units
• Password protected key lock
• Black finish
• Threaded receiver for clamp mounting
• DMX, Manual, Standalone (Auto Shows), Master/Slave, IR control

SPECIFICATIONS

• Light Source: 4 x 10W RGBW LED
• Beam Angle: 11°
• Field Angle: 21°
• Output: 743 LUX @ 5 meters
• Color Mixing: RGBW
• Strobe: 0-30 Hz
• Dimming: 4 dimming curve modes
• Control: W-DMX, Manual, Standalone, Master/Slave, Infrared remote
• DMX Channels: 4 / 6 / 10 / HSV / HSI
• Display: OLED function menu with 4 touch buttons
• Mains: 100 – 240 VAC, 50/60 Hz
• Consumption: 44W
• Power connections: Proprietary
• Battery: Lithium Ion
• Housing: Diecast Aluminum
• Finish: Black
• IP rating: IP65
• Cooling: Passive
• Max. Amblent: 40°C
• Min. Amblent: -20°C
• Max. Housing: 58°C
• Dimensions: 145 x 138 x 202 mm
• Weight: 3.68 KG
• Charging case dims: 470 x 555 x 547 mm
• Charging case weight: 22.3 kg (empty) ; 44.38 kg (loaded)
• Charging case power: Consumption : 350W / Charging output: DC 24V 14.58A
• Power connections: Neutrik Power Con

MAINTENANCE

Maintenance and cleaning the unit

• Make sure the area below the installation place is free from unwanted persons during setup.
• Swich of the unit, unplug the main cable and wait until the unit has cooled down.
• All screws used for installing the device and any of its parts should be tightly fastened and should not be corroded.
• Housings, fixations and installation spots (ceiling, trusses, suspensions) should be totaly free from any deformation.
• The main cables must be in impeccable condition and should be replaced immediately even when a small problem is detected.
• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might penetrate the unit and cause damage to it.

Troubleshooting

Contact an authorized service center in case of technical problems or not reported in the table can not be resolved by the procedure given in the table.

OPERATING ELEMENTS AND CONNECTIONS

MENU BUTTON OVERVIEW

OPERATING ELEMENTS AND CONNECTIONS (CHARGING CASE)

Flight case with PowerCon power in and six charging stations:

DIMENSIONS

PHOTOMETRICS

distance

(m)

color

| 1| 3| 5| 7| 10| Lumens
---|---|---|---|---|---|---
R| 4422| 491| 177| 90| 44| 335
G| 9823| 1091| 393| 200| 98| 572
B| 1541| 171| 62| 31| 15| 113
W| 12188| 1354| 488| 249| 122| 705
RGBW (lux)| 18580| 2064| 743| 379| 186| 1162

FUNCTIONS AND SETTINGS

MENU STRUCTURE

OPERATING ELEMENTS AND CONNECTIONS (CHARGING CASE)

1. Auto Show
   Five auto programs to choose from. Auto program #5 includes playback of programs 1-4.
   Speed can be adjusted 0-100 (slow to fast).

2. Static
   Select color presets under menu option or use option to mix custom colors.

3. Dimmer Mode
   Four selectable dimmer curves: , (fast), (medium),

   (slow) .

4. Back light
   Set delay time for menu display to go dark at either 10, 20 or 30 seconds or choose always ON.

5. Information
   Fixture software version and runtime clock.

6. DMX Address
   Set DMX starting address at a value between 001-512.

7. DMX Channel
   Select DMX mode: 3-channel HSV or HSI, or 4-, 6- or 10-channel operation.

8. Master/Slave
   Assign fixture to operate as either Master or Slave unit in configurations with multiple apollo fixtures.

9. White Balance
   Adjust RGB levels to achieve desired white light.

10. Wireless setting
    Turn wireless DMX receiver on/off or reset.

11. IR SETUP
    Turn IR sensor on/off to enable/disable infrared remote control.

12. KEY LOCK
    Password protection option.

13. FACTORY RESET
    Restore factory settings.

DMX CONTROL

4-Channel mode

6-Channel mode

3-Channel hsv mode

3-Channel hsi mode

DMX CONTROL : 10-CHANNEL MODE

WIRELESS DMX OPERATION

apollo can operate in W-DMX mode up to 300m from the W-DMX transmitter. The W-DMX receiver in the apollo must be paired with a W-DMX transmitter for wireless operation.

INITIAL SETUP

1. Turn on the W-DMX transmitter
2. Connect the W-DMX transmitter to a DMX controller
3. Position the Apollo fixture MAX 300m of the W-DMX transmitter in line of sight
4. Turn on the apollo fixture

CONFIGURATION

1. On the apollo control panel, go to DMX ADDRESS
2. Select the starting address
3. On the apollo control panel, go to WIRELESS SETTING
4. Set to ON (the apollo signal indicator will display a ? above the bars)
5.  Press the Reset button on the W-DMX transmitter (the apollo signal indicator will change to a symbol above the bars while connection is establish)

PAIRING
Once successfully paired, the apollo signal indicator will indicate the strength of the signal. At this point, the apollo is ready to be operated wirelessly by DMX. If the apollo fixture is subsequently used with a different W-DMX transmitter, follow steps below.

1. On the apollo control panel, go to WIRELESS SETTING
2. Select (the apollo signal indicator will display a ? above the bars)
3. Press the Reset button on the W-DMX transmitter
4. The apollo signal indicator will display the strength of the signal once pairing has been successful

INFRARED IR6 REMOTE CONTROL

The IR6 infrared controller enables remote control of the apollo. To pair the IR6 to the apollo, follow these steps:

1. Press MENU button until IR Setup is displayed
2. Press ENTER
3. Press UP or DOWN to turn infrared operation ON or OFF
4. Press ENTER

IR6 BUTTON FUNCTIONS
Buttons not listed below are not used with apollo

Contact Information

• Address: Stureparksvägen 7 45155 Uddevalla Sweden
• Phone: 0522 440 880
• Email: sales@interlite.se
• Web: www.interlite.se

References

• Interlite - LED & Trådlös belysning för Arkitektur, Scen och TV

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>