ET2 Contemporary Lighting E21563-142BK 3-Light LED Pendant Installation Guide
- June 1, 2024
- ET2 Contemporary Lighting
Table of Contents
ET2 Contemporary Lighting E21563-142BK 3-Light LED Pendant
Before Getting Started
Read the instructions carefully prior to assembling the product.
When you open the package with a sharp tool like a box knife, be careful not to damage the components inside.
Carefully remove all packaging materials and retain for future use.
Keep all hardware parts and packaging out of reach of children.
Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
Ensure that you have all required contents for complete assembly.
Take care when lifting. Assemble the product in close proximity to where you intend to install it.
Do not over tighten the screws and bolts as this may damage the threads.
Do not let children play with this product.
Risk of suffocation!
Keep packaging materials away from children.
Lamp Care Instructions
Carefully read through the instruction sheet before assembly and using the product.
Caution
there is a risk of shock!
Disconnect from power source before assembling or cleaning.
Switch off, unplug and allow bulb to cool before replacing bulb or cleaning.
Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire.
Check the product cord to be sure is free torn or frayed.
WARNING : Wires must to be connected to low Lil voltage driver and should not be connected directly to live wire or a short may occur.
Cleaning & Maintenance
On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, stone polish, & wood polish.
Clean with soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
Periodically (every 90-180 days) make sure that the screws are fully tightened.
Prolonged exposure to heat sources may ca use glazing, melting and scorching, or even cause color to fade.
PARTS
Before getting, started, ensure the package contains the following components:
A| 
| x1| | G| | x1
---|---|---|---|---|---|---
| H| | x3
| I| LED lighting power Pulssanced’ eclairage LEDModel:
NE024277060-2GH
Input/Entree :120-277Vac 0.32A 50/60Hz Output/Sortie:18-40Vdc 600mA Input
Power/Puissance d’entree:24W Max Dimmable at Vin/Dimmable at Vin=120Vac
PF >0.9 at Vin=120Vac/PF>0,9 avin =120VaG Size: 3.14″x1.41 W”x0.91″H|
x1
B| 
| x1| | | |
C| | x4| | | |
D| | x2| | | |
E| | x4| | | |
F| | x3| | | |
| | | | | |
Wiring Diagram
This fixture is equipped with an LED driver, please refer to the Wiring Diagram for more details
ITEM/MODEL: E21563-142BK
MUST be installed by an experienced professional
CRITICAL KNOWLEDGE of electronic lighting systems required
IMPROPER WIRING and/or INCORRECT DIMMER use can cause CATASTROPHIC DAMAGE! THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH DO NOT CUT FACTORY-MADE CONNECTIONS.
AC: 120-277V~50/60HZ
FACTORY CONNECTIONS (+) INNER CONUCTOR I OUTER MESH (-)
LED DRIVER DIAGRAM
SCHEMATIC FOR GENERAL REFERENCE ONLY
Customer Support
VERIFIED LIST OF TESTED DIMMERS
Lutron Diva DVCL-153P Lutron Diva DVELV-300P Lutron Diva Caseta PD-6WCL Lutron Maestro MACL-153M DEAKO-Smart Dimmer DEAKO-Single Dimmer LEVITON 6672-L LEVITON DSL06
GENERAL COMPATIBILITY
TR/AC/ FORWARD PHASE ELV / REVERSE PHASE Only at 120VAC
Due to inrush current, wattage should not exceeed 150W on a 600W dimmer
IMPORTANT!
If the control is not paired properly to LED fixtures, irreparable damage may occur.
If the dimmer you are using is not listed here, consult a lighting
professional or view our Dimming Compatibility Chart online:
www.et2online.com/led-dimmer
MUST be installed by an experienced professional CRIYICAL KNOWLEDGE of electronic lighting systems required
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>