ET2 E11078-122 Pebble 12 Light LED Pendant Instruction Manual
- September 19, 2024
- ET2
Table of Contents
**ET2 E11078-122 Pebble 12 Light LED Pendant Instruction Manual
**
LED LOW-VOLTAGE INSTRUCTIONS
Before Getting Started
Read the instructions carefully prior to assembling the product.
When you open the package with a sharp tool like a box knife, be careful not
to damage the components inside. Carefully remove all packaging materials and
retain for future use.
Keep all hardware parts and packaging out of reach of children. Choose a
clean, level, spaciousassembly area.
Avoid hard surfaces that may damage the product.
Ensure that you have all required contents for complete assembly.
Take care when lifting.
Assemble the product in close proximity to where you intend to install it.
Do not over tighten the screws and bolts as this may damage the threads.
Do not let children play with this product.
Risk of suffocation
Keep packaging materials away from children.
Lamp Care Instructions Carefully read through the instruction sheet before
assembly and using the product. Caution there is a risk of shock!
Disconnect from power source before assembling or cleaning. Switch off, unplug
and allow bulb to cool before replacing bulb or cleaning.
Only use the recommended bulb type and do not exceed the maximum wattage as it
could cause fire.
Check the product cord to be sure is free torn or frayed.
**WARNING:** Wires must to be connected to low voltage driver and should
not be connected directly to live wire or a short may occur.
Cleaning & Maintenance
On polished finishes, often using talc powder can reduce the appearance of
fingerprints and other smudges. For respective shade surfaces, use the
appropriate cleansers, i.e. glass cleaner, stone polish, & wood polish.
Clean with soft cloth and a mild detergent.
Do not use abrasive or harsh cleaners. Periodically (every 90-180 days) make
sure that the screws are fully tightened.
Prolonged exposure to heat sources may cause glazing, melting and scorching,
or even cause color to fade.
PARTS
Before getting, started, ensure the package contains the following components:
A| | x1| H|
NE 032120 YYY-2 G
3.25″x 1 .5″x 1″
| x 2
---|---|---|---|---|---
B
|
11842428
| x2| I|
GU 10 LED 120 V 7 W
BL7GU70Cu20v30(Included)
| x 3
C
| | x4| J|
x 9-40 x 1″
| x 4
D
| | x3|
k
| |
E
|
G L S 4 x 4 ‘
B L 8233 D 100 U 100
| x4|
L
| |
F
|
GLS 3×5″
BL8233D120U80
| x8|
M
| |
G| | Xi| N| |
This fixture is equipped with an LED driver, please refer to the Wiring Diagram for more details
WIRING DIAGRAM
DIMMER COMPATIBILITY
MUST be installed by an experienced professional CRITICAL KNOWLEDGE of
electronic lighting systems required.
IMPROPER WIRING and/or INCORRECT DIMMER use can cause CATASTROPHIC DAMAGE!
THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH
DO NOT CUT FACTORY-MADE CONNECTIONS.
AC:120-277V-50/60Hz
FACTORY CONNECTIONS (+) INNER CONUCTOR | OUTER MESH(-)
LED DRIVER DIAGRAM
SCHEMATIC FOR GENERAL REFERENCE ONLY
VERIFIED LIST OF TESTED DIMMERS
Lutron Diva DVCL-153
PLutron Diva DVELV-300P
Lutron Diva Caseta PD-6WCL
Lutron Maestro MACL-153 M D EA KO-Smart Dimmer DEAKO-Single Dimmer LEVITON
6672-LLEVITON DSL0 6
|
GENERAL COMPATIBILITYT
RIAC/FORWARD PHASE
ELV/REVERSE PHASE
Only at 120 VA C0-10 V /LOW VOLTAGE Work at 120-277 VAC
Due to inrush current, wattage should not exceeed 150W on a 600 W dimmer
| IMPORTANT!
If the control is not paired properly to LED fixtures, irreparable damage may
occur.
If the dimmer you are using is not listed here, consult a lighting professional or view our Dimming Compatibility Chart online: www.et2online.com/led-dimmer
---|---|---
MUST be installed by an experienced professional
CRITICAL KNOWLEDGE of electronic lighting systems required
© 2023 ET2 CONTEMPORARY LIGHTING
Item/Model Number : E11078-122 PEBBLE 12-Light LED Pendant
Lamping I Ampoule: 12 x LED 2W + 3 x GU10 LED 7W(Included) Please consult a qualified electrician prior to install
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>