ET2 E21181 Highball LED Mini Pendant Instruction Manual

September 16, 2024
ET2

ET2 E21181 Highball LED Mini Pendant

Specifications

  • Item/Model Number: E21181 Highball LED Mini Pendant
  • 1 x LED 10W (Included)
  • Dimensions: 2.55L x 1.18W x 0.9H

Before Getting Started

  • Read the instructions carefully before assembling the product.
  • When you open the package with a sharp tool like a box knife, be careful not to damage the components inside.
  • Carefully remove all packaging materials and retain them for future use.
  • Keep all hardware parts and packaging out of reach of small children.
  • Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
  • Ensure that you have all the required contents for complete assembly.
  • Take care when lifting. Assemble the product near where you intend to install it.
  • Do not over-tighten the screws and bolts as this may damage the threads.
  • Do not let children play with this product.

Risk of suffocation!
Keep packaging materials away from children.

Lamp Care Instructions

  • Carefully read through the instruction sheet before assembly and using the product.
  • Caution there is a risk of shock!
  • Disconnect from the power source before assembling or cleaning.
  • Switch off, unplug, and allow the bulb to cool before replacing the bulb or cleaning.
  • Only use the recommended bulb type and do not exceed the maximum wattage as it could cause a fire.
  • Check the product cord to be sure is free torn or frayed.
  • WARNING: Wires must be connected to a low-voltage driver and should not be connected directly to live wire or a short may occur.

Assembly

  1. Read the instructions carefully before assembling the product.
  2. Open the package carefully with a suitable tool to avoid damaging components.
  3. Remove all packaging materials and keep them for future use.
  4. Ensure e you have all required contents for complete assembly.
  5. Choose a clean, level assembly area away from hard surfaces that may damage the product.
  6. Assemble the product close to the installation area.

Safety Precautions

  • Keep hardware parts and packaging away from children.
  • Avoid over-tightening screws and bolts to prevent damage.
  • Do not let children play with the product.
  • Disconnect from the power source before assembling or cleaning.
  • Switch off, unplug, and allow the bulb to cool before replacing or cleaning it.

Cleaning and Maintenance

  • On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
  • For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, stone polish, & wood Polish.
  • Clean with a soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
  • Periodically (every 90-180 days) make sure that the screws are fully tightened.
  • Prolonged exposure to heat sources may cause glazing, melting, and scorching, or even cause color to fade.

Installation

  1. Refer to the Wiring Diagram for connecting wires properly.
  2. Ensure wires are connected to a low-voltage driver and not directly to live wires.

Additional Tips

  • Use talc powder on polished finishes to reduce fingerprints.
  • Avoid prolonged exposure to heat sources to prevent damage to the product.

PARTS

Before getting, started, ensure the package contains the following components:

This fixture is equipped with an LED driver, please refer to the Wiring Diagram for more details.

This fixture is equipped with an LED driver, please refer to the Wiring Diagram for more details.

WIRING DIAGRAM

IMPROPER WIRING and/or INCORRECT DIMMER use can cause CATASTROPHIC DAMAGE! THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH DO NOT CUT FACTORY-MADE CONNECTIONS.

VERIFIED LIST OF TESTED DIMMERS

  • Lutron Diva DVCL-153P
  • Lutron Diva DVELV-300P
  • Lutron Diva Caseta PD-6WCL
  • Lutron Maestro MACL-153M
  • DEAKO-Smart Dimmer
  • DEAKO-Single Dimmer
  • LEVITON 6672-L
  • LEVITON DSL06
  • GENERAL COMPATIBILITY
  • TRIAC / FORWARD PHASE
  • ELV / REVERSE PHASE
  • Only at 120VAC

IMPORTANT!
If the control is not paired properly with the LED fixtures, irreparable damage may occur. If the dimmer you are using is not listed here, consult a lighting professional or view our Dimming Compatibility Chart online: www.et2online.com/led-dimmer Due to inrush current, wattage should not exceed 150W on a 600W dimmer MUST be installed by an experienced professional CRITICAL KNOWLEDGE of electronic lighting systems is required.

MUST be installed by an experienced professional
CRITICAL KNOWLEDGE of electronic lighting systems is required.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ET2 User Manuals

Related Manuals