ET2 E30662 Serpentine LED Pendant Installation Guide

September 17, 2024
ET2

ET2 E30662 Serpentine LED Pendant Installation Guide

Read the instructions carefully prior to assembling the product.
When you open the package with sharp tool like a box knife, be careful not to damage the components inside.
Carefully remove all packaging materials and retain for future use.
Keep all hardware parts and packaging out of reach of children.
Chooseaclean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
Ensure that you have all required contents for complete assembly.
Take care when lfting. Assemble the product in close proximity to where you intend to install it.
Do not over tighten the screws and bolts as this may damage the threads.
Do ot let children play with this product.

Risk of suffocation!
Keep packaging materials away from children.

Lamp Care Instructions

Carefully read through the instruction sheet before assembly and using the product.

Caution there is arise of shock!
Disconnect from power source before assembling or cleaning.

Switch off, unplug and allow bulb to cool before replacing bulb or cleaning.
Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire.
Check the product cord to be sureis free torn or frayed

WARNING: Wires must to be connected to low voltage driver and should not be connected directly to live wire or a short may occur.

Cleaning & Maintenance

On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
For respective shade surfaces, use the appropriate cleansers, . glass cleaner, stone polish, & wood polish.
Clean with soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
Periodically (every 90-180 days) make sure that the screws are fully tightened.
Prolonged exposure to heat sources may cause glazing, meltingandscorching, or even cause color to fade.

PARTS

Before getting, started, ensure the package contains the following components:

A X1

B X1

C X2

8-32″25

D X1

E X1
STR05006BK-HF STR05012BK-HF 6″ Extension Stem x1 12″ Extension Stem x3

F X3

G X2
G5/32″™10

H X1
5/32*6

NE046277100-2GH
X1

Size: 35.4″Lx18.8″Wx10.8″H

This fixture is equipped with an LED driver, please refer to **Wiring Diagram

**

IMPROPER WIRING and/or INCORRECT DIMMER use can cause CATASTROPHIC DAMAGE!
THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH

DO NOT CUT FACTORY-MADE CONN ECTIONS.

AC: 120-277V~50/60HZ

LED DRIVER DIAGRAM

VERIFIED LIST OF TESTED DIMMERS
Lutron Diva DVELV-300P Lutron Diva Caseta PD-6WCL Lutron Maestro MACL-153M DEAKO-Smart Dimmer DEAKO-Single Dimmer LEVITON 6672-L LEVITON DSLO6

GENERAL COMPATIBILITY
TRIAC / FORWARD PHASE
ELV / REVERSE PHASE
Only at 120VAC

Due to inrush current, wattage should not exceeed 150W on a 600W dimmer

IMPORTANT!
If the control is not paired properly to LED fixtures, irreparable damage may occur.

If the dimmer you are using is not listed here, consult a lighting professional or view our Dimming Compatibility Chart online:
www.et2online.com/led-dimmer.

Documents / Resources

| ET2 E30662 Serpentine LED Pendant [pdf] Installation Guide
E30662 Serpentine LED Pendant, E30662, Serpentine LED Pendant, LED Pendant, Pendant
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ET2 User Manuals

Related Manuals