Roth AM-10 Connection Module Heating Cooling 230 V Basicline Instruction Manual
- September 9, 2024
- Roth
Table of Contents
AM-10 Connection Module Heating Cooling 230 V Basicline
“`html
Specifications:
-
Product Name: AM-10 Connection Module Heating/Cooling 230 V
Basicline -
Pollution Degree: 2
-
Resistance to Voltage Surges: 2500 V, as per EN 60730
-
Operating Voltage: 230 V
-
Admissible Ambient Temperature: 10-32°C
-
Admissible Ambient Humidity: 10-90% RH
-
IP Rating: IP20
-
Dimensions: 52mm
-
Number of Actuators: 2x
-
Pump Connection: 1x
-
Boiler Connection: 1x
-
Housing Material: Plastic Cover
Product Usage Instructions:
Safety Precautions:
1. Danger of electrocution. Mains powered parts are located
behind the cover. The device may only be opened by a trained
electrician.
2. Disconnect the device from the mains before beginning any
work on the electrical connections.
3. Only re-apply voltage once the housing has been closed and
all installation has been completed.
4. Do not leave the device unattended while the housing is
open.
Installation:
1. Follow the fitting instructions provided for the
electrician.
2. Ensure the device is disconnected from the power supply
before any assembly or disassembly.
Operation:
1. When using the Roth clock thermostat Basicline T, ensure a
bridge is in place between points A and B.
2. Refer to the provided table for shut-down delay settings and
switch configurations.
Maintenance:
1. To replace the fuse, disconnect the device from the power
supply before assembly or disassembly.
Additional Information:
For detailed programming and specific usage scenarios, refer to
the full user manual provided with the product.
FAQ:
Q: What should I do if I encounter an electrical issue while
using the AM-10 Connection Module?
A: In case of any electrical issues, immediately disconnect the
device from the power supply and seek assistance from a qualified
electrician.
Q: Can I leave the device unattended while performing
maintenance?
A: No, it is important to never leave the device unattended
while the housing is open to prevent any accidents or hazards.
“`
AM-10 connection module heating/cooling 230 V Basicline
EN Pollution degree 2; Resistance to voltage surges 2500 V; as per EN 60730
Fitting instructions for the electrician
1135007709
AM-10 230 V Basicline
50 122 °C °F
0 32
10-90%RH
IP20
EN60529
[mm] 52
è
2x
2x
1x
326,5
90
EN DANGER Danger of electrocution. Mains powered parts are located behind the cover. The device may only be opened by a trained electrician. Disconnect the device from the mains before beginning any work on the electrical connections. Only re-apply voltage once the housing has been closed and all installation has been completed. Do not leave the device unattended while the housing is open.
1
2 1
4
2b
2a
3
4
3
Night set-back mode
The bridge between A and B is required when using the Roth clock thermostat Basicline T.
4
NO
NC
Shut-down delay
0min 5min
23 23 10min 15min
23 23
Switch 1 = ON NO Switch 1 = OFF NC
Switch 2 OFF OFF ON ON
Switch 3 OFF ON OFF ON
Time 2 Min 7 Min 12 Min 17 Min
…t
Replacing the fuse
EN DANGER Danger of electrocution Disconnect the device from the power supply
before assembly or disassembly
DANGER
1
2
3
4
230 V T4A
1135007863 230 V humidity sensor with monitor functions
7% +
L N PE 230 V ~50 Hz
L N PE
L N PE 230 V ~50 Hz
L N PE
Basicline H 230 V
L NN 12 34 5
Basicline T 230 V
N L SL NSB S1 S2
7% +
Basicline H 230 V
L NN 12 34 5
Basicline H/C 230 V
C/O L N 12 34 5
7% +
WF
max. 18x 230 V, NC
Basicline H/C 230 V
C/O L N 12 34 5
max. 18x 230 V, NC
Heating/Cooling
/
AM-10 230 V
Heating
5 AM-10 230 V
Operating voltage Distributor fuse Circuits/zones
Time channels/set-back Admissible ambient temperature Admissible storage
temperature T
Admissible ambient humidity Number of actuators
Pump connection Boiler connection Set-back
Heating/ cooling
TB or dew point
Housing material
Plastic cover
Fitting
Connection terminals
Power cable
230 V~ ±10 % 50…60 Hz 230 V / T4A 10
2 0…50 °C -20…70 °C <80 % rF max. 18 max. 6 (2) A max. 6 (2) A
Potential-free contact input
Potential-free contact input
Potential-free contact input
Flame-retardant plastic, ABS iron-grey RAL7011
Transparent grey
Mounted on wall or 35 mm DIN rail
Terminals with spring technology, for 0.2 to 1.5 mm²
solid: NYM-J/NYM-O (5 × 1.5 mm² max.), flexible: H03V2V2H2-F / H05V2V2H2-F
Cord grip
Integrated in housing
Protection class 230 V
Type of protection
Accessories 1135007863
IP 20 (EN 60529)
III (EN 60730)
230 V humidity sensor with monitor functions
EN QR Code for complete product information
Roth UK Ltd. www.roth-uk.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>