NVIO AESS-BMM90H800L 4K Lite Varifocal Bullet Hybrid Camera Owner’s Manual
- June 13, 2024
- NVIO
Table of Contents
NVIO AESS-BMM90H800L 4K Lite Varifocal Bullet Hybrid Camera
Product Information
- Product Name: Luna Series | AESS-BMM90H800L
- Model Number: AESS-BMM90H800L
- Product Type: 4K Lite Varifocal Bullet Hybrid Camera
- Technical Specification:
- Camera Image Sensor: 1/3″ CMOS SENSOR
- Effective Pixels: 3480×2160
- Scanning System: Progressive
- Minimum Illumination: N/A (not mentioned in the manual)
- IR Distance: Maximum 40m
- IR On/Off Control: Auto/Manual
- IR LEDs: 8 IR ARRAY LED
- Lens Type: Motozoom lens
- Focal Length: 2.8-12mm
- Angle of View: N/A (not mentioned in the manual)
- Focus Control: Auto/Manual
- Video Resolution: 4K Lite (3480×2160)
- Video Output: 1-channel BNC high definition video output
- Day/Night: Auto (ICR)/Manual
- OSD Menu: Multi-language
- BLC Mode: BLC/HLC/DWDR
- WDR: WDR
- Gain Control: AGC
- Noise Reduction: 3D Noise Reduction
- White Balance: Auto/Manual
- Smart IR: Auto/Manual
- Electrical Power Supply: DC12V
- Power Consumption: 1W
- Main Features:
- 4in1 AHD, HD-CVI, HD-TVI, CVBS (UTC) compatibility
- IP65 weatherproof rating
Product Usage Instructions
-
Warnings & Precautions:
Before using the product, please read and follow the safety instructions provided in the user manual. -
Connections:
- Ensure that the camera is not powered before making any connections.
- Connect the video cable to the female bayonet BNC connector on the camera.
- Take the video cable to the monitor or DVR using an RG59 type coaxial cable and BNC connector.
- Alternatively, twisted pair cables can be used with balun converters.
- Check that the power supply is correct for the camera model used. It is recommended to use a 12Vdc / 1A or 12Vdc / 1.5A stabilized power supply unit with a standard 5.5mm pin.
- Be cautious of using power extension cables that are too long or have a small section, as they may cause excessive voltage drop when the IR illuminator is turned on.
-
Installation:
- To install the camera on a ceiling or wall with protected cable passage:
- Check the solidity of the structure and mark the points for camera fastening using a pencil.
- Drill the necessary holes for fastening the camera.
- For bullet type cameras:
- These cameras come with an integrated bracket for wall mounting.
- The bracket allows for the passage of cables inside it, protecting them from tampering attempts.
- Mount the camera at the cable outlet to avoid exposed cables.
- If the cables come from the side in an external duct, the fixing base has a lateral cable outlet slot.
- Use the provided plugs to fix the bracket to the wall or ceiling.
-
Framing Adjustment:
Adjust the framing of the camera as needed for optimal viewing angles. -
OSD Menu:
For detailed instructions on navigating and using the OSD menu, visit the website www.enviosecurity.com.
Note: Please refer to the complete user manual for additional information and instructions.
Main Features
- 1/3”CMOS SENSOR 4K Lite
- (3480×2160)
- 2.8-12mm Motozoom lens
- Maximum IR Led distance 40m
- 4in1 AHD, HD-CVI, HD-TVI, CVBS (UTC)
- 8 IR ARRAY LED
- IP65
- DC12V
Technical Specification
Camera|
---|---
Image Sensor| 1/3”CMOS SENSOR 4K Lite
Effective Pixels| 3480(H)×2160(V),8MP Lite
Scanning System| Progressive
Minimum Illumination| 0.05Lux/F1.6,(ACG ON), 0Lux IR on
IR Distance| 40m
IR On/Off Control| Auto / Manual
IR LEDs| 8 IR ARRAY LED
Lens|
Lens Type| Motozoom Lens
Focal Length| 2.8-12mm
Angle of View| 100°/45°
Focus Control| Automatic
Video|
Resolution| 3480×2160
Video Output| 1-channel BNC high definition video output
Day/Night| Auto (ICR) / Manual
OSD Menu| Multi-language
BLC Mode| BLC / HLC / DWDR
WDR| WDR
Gain Control| AGC
Noise Reduction| 3D
White Balance| Auto / Manual
Smart IR| Auto / Manual
Eelectrical|
Power Supply| 12V DC ±30%
Power Consumption| Max 5W (12V DC, IR on)
DIMENSION
Warnings & Precautions
Dear Customer, we thank you for choosing one of our products whose correct use guarantees solutions of the highest quality and reliability over time. This manual provides instructions for using the product.
Connections
- Make sure the camera is not powered before making connections.
- The video cable is connected to the female bayonet BNC connector, which is then taken to the monitor or DVR in general via RG59 type coaxial cable and BNC connector. Twisted pair cables can also be used with balun converters.
- Check that the power supply is correct and provided for the camera model used. The use of adequate power supply units is recommended. 12Vdc / 1A or 12Vdc / 1,5A stabilized is recommended. The pin required is the standard 5.5 mm. Beware of power extension cables that are too long or have a small section, which could introduce an excessive voltage drop, especially when the IR illuminator is turned on.
- The values expressed in the following table are to be considered at a temperature of 20 ° C [68 ° F].
Conductors section (AWG)| 24 AWG (0,22mm²)| 22 AWG (0,33mm²)| 20 AWG (0,52mm²)| 18 AWG (0,83mm²)
---|---|---|---|---
Resistance value (Ώ/m)| 0.078| 0.050| 0.030| 0.018
Voltage drop ( V/m)| 0.028| 0.018| 0.011| 0.006 - As the copper conductor section increases, there is a decrease in the resistance value () / m) and therefore in the voltage drop on the cable itself. Therefore, consider carefully the length and section of the cable during the design phase. Excessive distances between the power supply and the camera could compromise the correct functioning of the camera. The acceptable standard of variation of the supply voltage is 12Vdc ± 10%
Installation
This section indicates how to install the camera on a ceiling or wall with
protected cable passage. Check the solidity of the structure on which you
intend to fix the camera, mark the points with a pencil and drill the holes
necessary for its fastening.
Bullet type camera
The bullet cameras are equipped with an integrated bracket for wall mounting,
specially designed to allow the passage of cables inside it and protect them
from tampering attempts. The camera is generally mounted at the cable outlet
so as not to leave exposed cables. However, the fixing base also has a lateral
cable outlet slot if the cables come from the side in the external duct. The
bracket must be fixed to the wall or ceiling with the plugs provided
Framing adjustment
- Once correctly fixed to the wall / ceiling, point it in the desired direction and lock it (it may vary from model to model) by tightening the screws with the supplied Allen key.
- Fixed lens cameras (IR up to 20m) do not require focus as they are factory set for most applications.
- To ensure excellent image quality even in low light conditions, all models are equipped with a Day & Night function with removal of the IR filter to automatically switch from color to B / W. In addition, all models are equipped with integrated 850nm IR LED illuminators, for adequate illumination of the area being shot. Be careful not to install the camera very close to strong light sources or in places subject to reflection of light that could compromise the correct vision of the camera.
OSD menu
Depending on the camera models. This model has a coaxial control:
- Access the DVR menu in the appropriate coaxial configuration section (in ENVIO DVRs this setting is called “XVI control”. Press the central console button that appears on the monitor to enter the menu home page.
- Select topic / function of interest using the scroll up / down buttons.
- Use the left or right buttons to select the different operating modes.
- Move to [EXIT] and press the center button to exit the setting mode, without saving the settings.
- Navigate to [SAVE & EXIT] and press the center button to exit the setting mode, saving the settings.
For the full OSD manual visit www.enviosecurity.com