allen roth SS23773 Pendant Light Instruction Manual
- June 1, 2024
- Allen+Roth
Table of Contents
allen roth SS23773 Pendant Light
Thank you for purchasing this ALLEN + ROTH product. We’ve created these easy-
to-follow instructions to ensure you spend your time enjoying the product
instead of putting it together. But, if you need more information than what is
provided here, please visit Lowes.com, search the item number and refer to the
Guides & Documents tab on the product’s page.
Note: You must refer to the full manual online for the complete safety
information, care instructions, troubleshooting and warranty.
PACKAGE CONTENTS
HARDWARE CONTENTS
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product. Failure to do so could lead to electrical shock, fire or other injuries that could be fatal./Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. No hacerlo podría provocar descargas eléctricas, incendios u otras lesiones, las que pueden ser fatales.
DANGER
- DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. Installing a fixture into an electrical system not having a proper grounding means could cause serious injury or death.
- DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying wire or the white (NEUTRAL) house wire. Connection of the bare or green fixture ground wire to the black or white house wires could cause serious injury or death.
- DO NOT damage or cut the wire insulation (covering) during the installation of the fixture. DO NOT permit wires to contact any surface having a sharp edge. To do so may could cause serious injury or death.
WARNING
- All electrical connections must be in agreement with local codes and ordinances, the National Electric Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn about your local codes, permits and/or inspections. Risk of fire – most dwellings built before 1985 have supply wire rated for 140 °F. Consult a qualified electrician before installation.
- To avoid personal injury, gloves may be necessary while handling fixture parts with sharp edges.
- Failure to caulk fixture mounting surface with silicone weather sealant may result in water damage in outlet box, which may cause electrical malfunction or electrical shock.
- DO NOT suspend any fixture by the house wires.
- A fixture must always be mounted directly to an outlet box or to a mounting strap which is first attached to the outlet box.
- Suspending a fixture by the house wires and wire connectors could result in the fixture falling, with the possibility of personal injury, electrical shock or fire.
- To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture.
- If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician.
CAUTION
- TURN OFF ELECTRICITY at circuit breaker box before beginning installation by switching the circuit breaker off.
- If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture.
- Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
- All fixtures must be mounted to an outlet box that is supported by the building structure.
- If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type to use as well as the electrical rating required.
- DO NOT use bulbs having a wattage greater than the maximum value stated on the fixture. The use of a bulb with higher wattage than specified will increase temperatures and risk of fire
- If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type to use as well as the electrical rating required.
- Before installation is complete, carefully check all screws, bolts and nuts on fixture to ensure that they are secure.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with the package contents list and hardware contents list.If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 30 minutes
FEELING CONFIDENT
Visit US – lowes.com, Canada – lowes.ca
for more information:
INSTALLATION OVERVIEW
ALLEN + ROTH and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
Questions, problems, missing parts? Before returning, contact us on 866-439-9800,8 a.m. – 8 p.m., EST,Monday – Sunday or ascs@lowes.com.