allen roth 5632010 Outdoor Wall Lantern Light Instruction Manual
- May 15, 2024
- Allen+Roth
Table of Contents
Allen Roth 5632010 Outdoor Wall Lantern Light
Specifications:
- Item Numbers : #5632010, #5632011
- Model Numbers : WLS144BK, WLM144BK
- Product Type : Outdoor Wall Lantern
- Trademark : ALLEN+ROTH
- Approved for Use in Wet Locations
Product Usage Instructions:
Package Contents:
- Fixture – Quantity : 1
- Mounting Plate – Quantity: 1 (preassembled to fixture)
- Washer – Quantity : 2 (preassembled to a mounting plate screw)
- Mounting Plate Screw – Quantity : 2 (preassembled to fixture)
Hardware Contents:
Machine Screw – Quantity: 2
Safety Information:
Before beginning assembly, ensure all parts are present. Do not attempt assembly if any part is missing or damaged.
Tools Required for Assembly (not included):
- Flathead Screwdriver
- Phillips Screwdriver
- Wire Strippers
- Pliers
- Wire Cutters
- Safety Glasses
- Stepladder
- Electrical Tape
- Silicone Weather Sealant (and tool to apply sealant)
Assembly Instructions
-
1. Turn off circuit breakers and wall switches to the fixture supply line leads. - Remove the existing fixture and disconnect all electrical wiring.
- Remove the mounting plate from the fixture by unscrewing the mounting plate screws and washers from the fixture. Save these for later use.
- Attach the mounting plate to the outlet box using the existing washers and outlet box screws or machine screws. Ensure the mounting plate is parallel with the floor and ceiling as needed.
- Unwrap bare wire from black and white wires on the fixture. Prepare wires by stripping insulation from wire ends.
Note: Ensure proper wire connections are made and consult an electrician if needed for larger wires or multiple connections.
FAQ
- Q: What should I do if any parts are missing or damaged?
- A : Do not attempt to assemble the product. Contact customer support at 866-439-9800 for assistance.
- Q: Can I mount the fixture to a plastic outlet box?
- A : Plastic outlet boxes are not recommended for mounting the fixture. It should be mounted to an outlet box supported by the building structure.
ALLEN+ROTH and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved
Purchase Date
OUTDOOR WALL LANTERN APPROVED FOR USE IN WET LOCATIONS
ALLEN+ROTH and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
Thank you for purchasing this ALLEN + ROTH product.
Questions, problems, missing parts?
Before returning, contact us on 866-439-9800, 8 a.m. – 8 p.m., EST,
Monday – Sunday or ascs@lowes.com.
PACKAGE CONTENTS
HARDWARE CONTENTS
SAFETY INFORMATION
- READ AND SAVE THESE INSTRUCTIONS.
DANGER
- For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to fire, electrical shock or other injuries that could be hazardous or even fatal.
- If using this light fixture in a WET location, this light fixture must be connected to a supply circuit that is protected by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal injury, electrical shock or death.
- DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. Installing a fixture into an electrical system not having a proper grounding means could cause metal parts of the fixture to carry electrical currents if any of the fixture wires, wire connections or splices were to become broken, cut or loose during the mounting or normal operation of the fixture. Under this condition, anyone coming in contact with the fixture would be subject to electrical shock, which could cause serious injury or death.
- DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying wire or the white (NEUTRAL) house wire. Connection of the bare or green fixture ground wire to the black or white house wires may cause metal parts of the fixture to carry electrical currents. Under this condition, anyone coming in contact with the fixture will receive an electrical shock, which could cause serious injury or death.
- DO NOT damage or cut the wire insulation (covering) during the installation of the fixture. DO NOT permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electrical shock.
WARNING
- All electrical connections must be in agreement with local codes and ordinances, the National Electric Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn about your local codes, permits and/or inspections. Risk of fire – most dwellings built before 1985 have supply wire rated for 140 °F. Consult a qualified electrician before installation.
WARNING
- To avoid personal injury, the use of gloves may be necessary while handling fixture parts with sharp edges.
- DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to an outlet box or to a mounting strap which is first attached to the outlet box. The outlet box must be supported by the building structure. Wire connectors will not support the weight of a fixture.Suspending a fixture by the house wires and wire connectors will result in the fixture falling, with the possibility of personal injury and the danger of electrical shock or fire.
- To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
- To reduce the risk of damage to the fixture, DO NOT use power tools to assemble any part of the fixture.
- Failure to caulk the fixture mounting surface with silicone weather sealant may result in water damage in the outlet box, which may cause electrical malfunction or electrical shock.
- To avoid water damage to the fixture or possible electrical malfunction, install the fixture at least 4 ft. above the ground/floor.
CAUTION
- TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching the circuit breaker off).
- If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
- All fixtures must be mounted to an outlet box that is supported by the building structure.
- DO NOT use bulb having a wattage greater than the maximum value stated on the fixture. The use of a bulb with a higher wattage than specified will increase temperatures and risk of fire.
- If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type to use as well as the electrical rating required.
PREPARATION
Before beginning assembly of a product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
- Estimated Assembly Time: 30 minutes
- Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Screwdriver, Wire Strippers, Pliers, Wire Cutters, Safety Glasses, Stepladder, Electrical Tape, Silicone Weather Sealant (and tool to apply sealant)
- Helpful Tools (not included): A/C Tester Light, Do-It-Yourself Guide, Soft Cloth, Level
ASSEMBLY INSTRUCTIONS
- Turn off circuit breakers and wall switches to the fixture supply line leads.
- DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death.
- Remove the existing fixture and disconnect all electrical wiring.
- Remove mounting plate (B) from fixture (A) by removing mounting plate screws (D) and washers (C) from the fixture (A). Save mounting plate screws (D) and washers (C) for later use.
- Attach mounting plate (B) to outlet box (not included) using the existing washers and outlet box screws or the machine screws (AA). NOTE: If the outlet box screws (not included required for your outlet box are of a different size than the machine screws (AA), consult with a licensed electrician before proceeding. Use a level (not included) to adjust mounting plate (B) so mounting plate (B) is parallel with floor and ceiling as needed. Tighten machine screws (AA) completely to secure the mounting plate (B).
- CAUTION : The fixture (A) must be mounted to an outlet box that is supported by the building structure and can support the weight of the fixture. Plastic outlet boxes are not recommended.
Hardware Used
AA Machine Screw
- 5a. Unwrap BARE wire from BLACK and WHITE wires on fixture (A). Prepare wires by stripping 3/4 in. of insulation from wire ends using wire strippers (not included).
- 5b. Connect BARE/GREEN ground wire from outlet box to BARE ground wire from fixture (A) with lever wire connector by lifting the lever of the connector up, inserting the wire into the connector and dropping the lever back down to lock the connection. Connect WHITE wire from fixture (A) to WHITE wire from the outlet box using existing wire connector or reassembled lever wire connector. Connect the BLACK wire from fixture (A) to the BLACK wire from the outlet box using the existing wire connector or preassembled lever wire connector.
- NOTE : GENTLY pull on wires to confirm the lock is engaged.
- WARNING : Never connect the ground wire to WHITE or BLACK power supply wires.
WARNING : To reduce the risk of fire, electrical shock or personal injury, preassembled lever wire connectors are designed to accept only one 12-gauge house and two lead wires from the light fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
- 6. Wrap electrical tape (not included) around each individual preassembled lever wire connector down to the wire.
- WARNING : Make sure no bare wire or wire strands are visible after making connections. Push preassembled lever wire connectors gently back into the outlet box. Carefully push excess wiring into the outlet box.
Push reassembled lever wire connectors gently back into the outlet box. Carefully push excess wiring into the outlet box.
- 7. Attach fixture (A) to mounting plate (B) using the mounting plate screws (D) and washers previously removed.
-
- NOTE : Before tightening mounting plate screws (D) completely, use level (not included) to check fixture (A) — adjust if necessary.
- 8. Install one 60-watt max. standard-base incandescent bulb (not included) or CFL/LED equivalent.
- WARNING : When replacing the bulb, please allow bulb and fixture (A) to cool down before touching them.
- 9. Restore power and test fixture (A). If the light does not function, please refer to
- TROUBLESHOOTING on the following page.
-
- 10. After completing the installation, caulk the mounting surface of fixture (A) with silicone weather sealant (not included).
- WARNING : Failure to caulk the fixture mounting surface with silicone weather sealant may result in water damage in the outlet box, which may cause electrical malfunction or electrical shock.
CARE AND MAINTENANCE
- Shut off the main power supply. Wipe the fixture with a soft, damp cloth. Use mild cleaner to clean the shade. Do not use an abrasive cleaner on the fixture.
TROUBLESHOOTING
WARNING : Before beginning work, shut off the power supply to avoid electrical shock.
WARRANTY
The distributor warrants all of its lighting fixtures against defects in materials and workmanship for five (5) years from the date of purchase. If within this period the product is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The distributor will, at its option, repair, replace or refund the purchase price to the consumer. All costs of installation and removal of the fixture is the responsibility of the consumer. This warranty does not cover fixtures becoming defective due to misuse, accidental damage or improper handling and/or installation and specifically excludes liability for direct, incidental or consequential damages, improper packaging of returned products and acts of God. As some states do not allow exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This warranty gives you specific rights and you may also have other rights which may vary from state to state.
Printed in China
Documents / Resources
|
allen roth 5632010 Outdoor Wall Lantern
Light
[pdf] Instruction Manual
5632010 Outdoor Wall Lantern Light, 5632010, Outdoor Wall Lantern Light, Wall
Lantern Light, Lantern Light, Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>